DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Spark Plug Wires
Go
New
Find
Notify
Tools
Reply
  
Spark Plug Wires
 Login/Join
 
DRR S/Pro
posted
I’m replacing ignition items. One thing I wanted to change to was under header sleeved plug wires. I purchased these Moroso Technologies from Smiley’s some years ago on the recommendation of a racer on DRR I believe and have been sitting on the shelf. They were much less in price from what Moroso sells and only difference I can see/ measure is that the sleeves are solid black and the boot ends say Smiley’s.

I pulled the sleeve off the distributor coil wire and the wire was marked Moroso Wire Technologies. These are 350 ohm/ft same as THIS Moroso Ultra model.

I’ve run wires with as much as 200 ohm/ft prior with excellent results. I expect these 350 ohm/ft to be the exact same performance as if I were running the Moroso Ultra 40 or MSD 8.5 Super Conductor with my 7720 Grid. Here’s where they might be superior.

There could be times where ignition interference from spark plug wires could cause unexplainable events in digital devices. Because of the slightly higher resistance of these wires it could possible make a difference in correcting these events.

Analog ignition though, will withstand much more ignition interference and work properly.

 
Posts: 5550 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post
DRR Top Comp
Picture of Curly1
posted Hide Post
I have been running those plug wires for more than 10 years with very good results. My Data Logger monitors most everything and have had no problem with interference.
Highly recommend the Smileys Racing / Moroso Ultra 40 wires.


https://postimg.cc/gallery/np3zpruo/
"Dunning-Kruger Effect"
-a type of Cognitive bias where people with little expertise or ability assume they have superior expertise or ability. This overestimation occurs as a result of the fact that they do not have enough knowledge to know they don't have enough knowledge.

Before you argue with someone ask yourself, "Is this person mentally mature enough to grasp the concept of a different perspective?" If not there is no point to argue.

4X NE2 CHAMPION. 2020 TDRA NE2 Champion
 
Posts: 12569 | Location: United States of Texas | Registered: April 02, 2011Reply With QuoteReport This Post
DRR Top Comp
Picture of Curly1
posted Hide Post
For any of you that need Custom wires Ton's Performance wires makes some really nice wires reasonably priced. On one of my Aircraft I had to get custom wires made and they turned out really nice. He can make each one length you need with ends you need and it did not take long.

For standard plug wires hard to beat the Smileys racing / Moroso Ultra 40. I hate paying $185 for Moroso wires and can get same thing for $99 at Smileys.


https://postimg.cc/gallery/np3zpruo/
"Dunning-Kruger Effect"
-a type of Cognitive bias where people with little expertise or ability assume they have superior expertise or ability. This overestimation occurs as a result of the fact that they do not have enough knowledge to know they don't have enough knowledge.

Before you argue with someone ask yourself, "Is this person mentally mature enough to grasp the concept of a different perspective?" If not there is no point to argue.

4X NE2 CHAMPION. 2020 TDRA NE2 Champion
 
Posts: 12569 | Location: United States of Texas | Registered: April 02, 2011Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
https://sparkplugwires.com/

Talk to Mark.


California Screaming!
Raceless in California!
 
Posts: 6952 | Location: Vacaville  | Registered: January 07, 2004Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
^^^^^^^ Excellent selection and pricing, NICE!!!!
 
Posts: 5550 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post
DRR Pro
posted Hide Post
I use the MSD 8.5 super conductor & the reason is the multi-angle spark plug boots.

2BKING Smile

Relaxing


1980 Camaro
Taking the Best Working Small Tire Shyt Box & making it Greater Than Before!
3100 lbs.
Pump Gas 436
 
Posts: 4088 | Location: NV. | Registered: October 20, 2006Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
Magnecor FTW!


Clowns to the left of me, Jokers to the right. Here I am.......
 
Posts: 11717 | Location: stuck in the middle with you! | Registered: March 11, 2002Reply With QuoteReport This Post



DRR Sportsman
posted Hide Post
I have been using Firecore wires since they started. Never had an issue and we currently have them on three cars. Switch from MSD stuff and these are much nicer and will never go anywhere else.


"I am not ashamed to confess I am ignorant of what I do not know."
Marcus Tullius Cicero
 
Posts: 2070 | Location: Las Vegas, NV | Registered: April 14, 2004Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
quote:
Magnecor FTW!


Magnecor KV85 Competition are 2.2k ohms per ft… just saying
 
Posts: 5550 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post
DRR Pro
Picture of rusty
posted Hide Post
mark have you seen the ohms affect us and at what point


thank you, president Trump
 
Posts: 4429 | Location: texas | Registered: February 17, 2006Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
^^^^^I have no idea. Someone like Joe and his dyno experience might have an idea or opinion.

Obviously, the more wire resistance the less spark current at the spark plug. At what point it affects performance depends on engine/ fuel (NA vs boost , gas vs methanol). 40 ohm ft delivers more than 350 ohm ft, and I’m always for more.

Using a slightly higher ohm/ft wire with an ECU and digital dash (mine) might be beneficial although I just removed an 8 yr old set of MSD 50 ohm problem free without and now with ECU.

I prefer the higher mj ignitions (160+ mj), mating coil and multi spark.

I’m unsure what they are using to produce the spark in THIS TEST , but it might give you an idea of what slightly more resistance does to the spark. I agree with several comments that once you reach the point of enough spark to satisfy combustion, anything more does little.

My spark plugs went from .030 new to .040 gap in 250 runs. 250 runs later at 500 runs they were .044 gap. Put a new set in and ran the exact same ets. I’ll be interested in seeing the future spark plug gap results with these new slightly higher ohm wires being installed.
 
Posts: 5550 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post
DRR Pro
Picture of rusty
posted Hide Post
quote:
posted November 17, 2026 08:06 PM Hide Post
^^^^^I have no idea. Someone like Joe and his dyno experience might have an idea or opinion.

Obviously, the more wire resistance the less spark current at the spark plug. At what point it affects performance depends on engine/ fuel (NA vs boost , gas vs methanol). 40 ohm ft delivers more than 350 ohm ft, and I’m always for more.

Using a slightly higher ohm/ft wire with an ECU and digital dash (mine) might be beneficial although I just removed an 8 yr old set of MSD 50 ohm problem free without and now with ECU.

I prefer the higher mj ignitions (160+ mj), mating coil and multi spark.

I’m unsure what they are using to produce the spark in THIS TEST , but it might give you an idea of what slightly more resistance does to the spark. I agree with several comments that once you reach the point of enough spark to satisfy combustion, anything more does little.

My spark plugs went from .030 new to .040 gap in 250 runs. 250 runs later at 500 runs they were .044 gap. Put a new set in and ran the exact same ets. I’ll be interested in seeing the future spark plug gap results with these new slightly higher ohm wires being installed.

thanks mark


thank you, president Trump
 
Posts: 4429 | Location: texas | Registered: February 17, 2006Reply With QuoteReport This Post
DRR S/Pro
Picture of Lenny5160
posted Hide Post
quote:
Originally posted by markemark:
My spark plugs went from .030 new to .040 gap in 250 runs. 250 runs later at 500 runs they were .044 gap. Put a new set in and ran the exact same ets. I’ll be interested in seeing the future spark plug gap results with these new slightly higher ohm wires being installed.


Many years ago I found noticeable HP on the dyno by closing my gap from .050 to .030. It was something like 10 HP. This was with Ron's injection and I believe a 7AL-2.

I don't even check plug gap anymore - just install them out of the box. It seems most plugs are in the .028-.032 range.


Tony Leonard
 
Posts: 5855 | Location: Inver Grove Heights, MN | Registered: March 18, 2004Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
Here’s the A-B-A test I did yrs ago shortly after I purchased a second 7730 controller as a backup spare. I took an old 6al and put the correct/ same ends as the 7720 to make it a quick direct install replacement if the 7720 failed. The only other item needed was the included 7730 legacy cable and a program update. The 7720 paired with the 8261 HVC-2 coil will output 220 mJ. An old 6al is 105 -110 mJ.

I made the first two passes of the day with the 7720. I switched to the 6al during the event and ran the next 2 passes still running same et. Switched back to 7720 still running same ET. I have no idea the spark plug gap when I did the test but probably less than .040 guessing.

I still carry this 6al for a spare if the 15 yr old 7720 fails. MSD 7720 are repairable by the factory.




Here’s my opinion on ignition that uses a distributor. I prefer having more spark power than needed to the point of what MSD 7720 offers (220 mJ max). This will power NA with nitrous/ boost. If I felt the need for more ignition, I’d purchase the MSD Power Grid Single Channel PRO 600 (8001). This plugs directly into 7730 and is fully programmable from 250-400 mJ Normal range to 350-680 mJ High power range. The only time I would use High power is during a run at WOT if Normal range was not enough.
 
Posts: 5550 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post



  Powered by Social Strata  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Spark Plug Wires

© DragRaceResults.com 2026