DRR Trophy
| 1000-1300hp Without knowing any info, it's a complete crapshoot.
Nick Craig
1971 Camaro Split Bumper
376ci LS3
|
| | | Posts: 410 | Location: Ohio | Registered: December 28, 2013 | 
IP
|
|
DRR S/Pro
| quote: Originally posted by NC3x58:
1000-1300hp
Without knowing any info, it's a complete crapshoot.
I mean you couldn't miss that by a 300HP spread  If done correctly 1200 isn't out of the question. I think a conservative figure is 1100-1125 on a more "mild" build. |
| | |
DRR Trophy
| As mentioned, depends on a lot of things. For reference, our 615 Dart 11* (untouched heads), Profiler intake, similar on compression and lift, with q15 fuel, one 1150 carb, made right at 1200.
Had Dart run their "D" program through them, went up to 16:1 compression and a cam to take advantage of the porting, and picked up 50 HP to be at 1250. This combo, with a Super Comp style converter (slow 1.03 60ft) at 1920 lbs has been 6.99 and almost 192 at 2000ft DA.
Based on what you said, if it doesn't make a minimum of 1200 I'd be disappointed (even on a tight dyno). |
| | | Posts: 34 | Location: Nebraska | Registered: October 09, 2019 |
IP
|
|
DRR Trophy
| quote: posted November 06, 2020 03:54 PM Hide Post
As mentioned, depends on a lot of things. For reference, our 615 Dart 11* (untouched heads), Profiler intake, similar on compression and lift, with q15 fuel, one 1150 carb, made right at 1200.
Had Dart run their "D" program through them, went up to 16:1 compression and a cam to take advantage of the porting, and picked up 50 HP to be at 1250. This combo, with a Super Comp style converter (slow 1.03 60ft) at 1920 lbs has been 6.99 and almost 192 at 2000ft DA.
Based on what you said, if it doesn't make a minimum of 1200 I'd be disappointed (even on a tight dyno).
Well that's good news! |
| | | Posts: 82 | Location: Salt Lake City | Registered: August 06, 2009 |
IP
|
|
DRR S/Pro
| quote: Originally posted by RacerVX54:
if i had a 632 and it didn't make 1200 i would be really sad
Mine only made 1020 but it has conventional heads and less than .850 net lift. It’ll still run 8.90 at 180+ so it’s good enough for me considering the budget.
Tony Leonard
|
| | | Posts: 3244 | Location: Inver Grove Heights, MN | Registered: March 18, 2004 |
IP
|
|
DRR S/Pro
| quote: Originally posted by bbtommyd:
Here is what I know, 2 1150's, sheet metal TRE intake, all I know is 15-1 to 15.5-1 compression cam is over .900 lift, non oxygenated fuel etc.
Assuming the heads are ported a well built 632 with those heads has the capability to make 1350 HP more or less with that compression and lift close to 1". Anything less than 1300 would be sub par IMO or the combo was just not built to utilize the full potential of those heads. |
| | | Posts: 2163 | Location: Tewksbury, MA,USA | Registered: November 03, 2000 |
IP
|
|
DRR Sportsman
| quote: Originally posted by TonyB6255:
My 632* 11 degree with Slawko ported heads made 1250 with a Book 1250 carb. It went 6.95 at 193 in decent air. In better air it would probably would have went 6.90 as it was going 4.40 @ 157 in July this year.
Is this in a dragster? |
| | | Posts: 48 | Location: litchfield n.h. | Registered: January 28, 2008 |
IP
|
|
s... Let GXP7093 appear!
