|
|
Bracket Talk
Bracket Talk Forum
Tech Talk - by Abruzzi
MSD 6523 ULTRA 6AL PLUS LAUNCH RETARD HELPGo ![]() | New ![]() | Find ![]() | Notify ![]() | Tools ![]() | Reply ![]() | |
| DRR Trophy |
I hooked up a new 6523 6AL programable Plus box . 99% sure very thing is hooked up right, dark blue wire to transbrake/delay box . I built a 2D timing curve to calm things down at launch, saved it, loaded it, but it doesn't retard any when the transbrake releases. I was able to easily a step retard to accomplish a similar timing curve and that works triggering from the delay box tstop timer. What am I missing ?ULTRA | ||
|
| DRR Trophy |
Use the pink wire to activate retard curve . Do not go more than 9.9 degrees of retard. The dark blue wire is for the two step . | |||
|
| DRR S/Pro |
The release of the dark blue launch input starts the Launch Timing Plot. Pink wire is Step Retard, timing retard on demand... ie… Nitrous, ect. Try leaving the Launch Rev Limiter Latched “Not” activated. | |||
|
| DRR Trophy |
Markemark, thanks for the suggestion I tried latch both ways, same result, I don't think the curve I saved is actually loading. when I view the graph for launch retard it is not there, just a flat line, no retard | |||
|
| DRR S/Pro |
Android or Apple? Maybe a step missed in saving first then loading..?? What’s disappointing is they say the Plus works in MSD View (Windows laptop) but I don’t see a product listing for the 6523. | |||
|
| DRR Trophy |
I have ran mine the way i explained for three years now. I went the way you are trying to the point that the tech guy got to no my voice. So this is what works for me. | |||
|
| DRR S/Pro |
Maybe try this... AI Overview When the MSD Ultra 6AL Plus (PN 6523) will not save, load, or apply a launch retard setting, the issue usually comes down to either a 10-degree retard limit on the box, how the timing curve starts at 0, or whether you are using the MSD Ultra 6AL mobile app vs. MSD View PC software. 1. Check for the 10-Degree Hardware Limit The MSD 6523 supports a maximum of 10 degrees (0 to 9.9°) of retard. • Why it won't save/load: If you build a launch retard curve or step setting exceeding 9.9° (such as 15° or 20°), the box will reject the value or fail to apply it properly. • Fix: Keep all launch and step retard values at or below 9.9 degrees. 2. Verify the Starting Point of Your Timing Curve If you are building a time-based launch retard curve (ramping timing back in after launch), a user on Facebook noted a specific quirk with how the 6523 reads curves: • Why it fails to load/run: The curve must begin with a 0-degree starting point before dropping into your retard value, rather than starting directly at the retarded number. • Fix: Set your initial point at 0.0s / 0°, and place your target retard immediately after (e.g., 0.01s / -8°), then ramp back to 0° over your desired launch window. 3. Saving and Loading in the App vs. MSD View Software • MSD Ultra 6AL App (Bluetooth): Open the MSD Ultra 6AL app, tap Settings, and verify that your Bluetooth connection is active (the ignition must have switched 12V power on, though the engine does not need to be running). After adjusting the slider or table, you must tap Write / Save to Device before closing the app or cycling key power. • MSD View (PC via USB): If the mobile app refuses to hold the file, connect a laptop via the USB port using MSD View. Create the file offline, click Write to Box, then disconnect and cycle the 12V ignition power off for 10 seconds before reconnecting to confirm the box retained the tune. 4. Confirm the Trigger Wire (Blue vs. Pink) If the setting saves in the app/software but never activates on the track, verify which wire is triggering it: • Blue Wire (2-Step / Launch): Activates the Launch Rev Limiter when 12V is applied (or switched ground, depending on your harness/box configuration). • Pink Wire (Step Retard): Activates the Step Retard when 12V is applied (or above a set RPM threshold). If your launch retard is tied to the step retard function rather than a launch curve, it will not engage unless the Pink wire sees 12V at the same time as your transbrake/2-step. Quick Diagnostic Check 1. Turn the ignition key ON (engine off) and connect via Bluetooth or USB. 2. Set a test retard of 5.0 degrees (well under the 9.9° cap). 3. Save/Write to the box, turn the key OFF for 10 seconds, turn the key back ON, and re-read the box. • If 5.0° stays saved: Your previous file had an out-of-range value (>9.9°) or invalid curve point. • If 5.0° reverts to 0: Check the Diagnostics > Alerts tab in the app for a voltage or memory fault, and ensure battery voltage is above 12V while writing to the unit. | |||
|
| DRR S/Pro |
I stand corrected on what I wrote about MSD View and 6523 Ultra Plus. MSD View will use an auto detect when attached to this control | |||
|
| DRR Trophy |
Thank you all for the help. Turns out that using an Android phone I had to turn it 90* to see and tap the accept button which actually sends the curve to the box, working as intended now. | |||
|
| DRR S/Pro |
^^^^^^Excellent. I assume no slider bar in the lower part of the view when held normal to display the Accept Button. Thanks for the update! | |||
|
| Powered by Social Strata |
| Please Wait. Your request is being processed... |
|
Bracket Talk
Bracket Talk Forum
Tech Talk - by Abruzzi
MSD 6523 ULTRA 6AL PLUS LAUNCH RETARD HELP

