DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    "Family Tradition" a build for Daughter & Grandchildren
Page 1 2 3 4 
Go
New
Find
Notify
Tools
Reply
  
"Family Tradition" a build for Daughter & Grandchildren
 Login/Join
 
DRR Pro
Picture of SlyFox
posted Hide Post
Awesome


Mike
 
Posts: 1600 | Location: Marietta, GA | Registered: December 09, 2005Reply With QuoteReport This Post
DRR Pro
posted Hide Post
It is not necessary to have caster wheels, but it helps Smile


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Pro
posted Hide Post
caster wheels


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Pro
posted Hide Post
Strings are useful tools


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Pro
posted Hide Post
Strings in use


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
Larry, you should assemble all you photos into a how to book. Like the old Smokey Yunick manual. You have the knowledge, might as well share and profit at the same time.


Illegitimi non carborundum
 
Posts: 2371 | Location: OKC, OK | Registered: February 15, 2008Reply With QuoteReport This Post
DRR Pro
Picture of Rob7181
posted Hide Post
Awesome job as always Larry


Rob Robertson
 
Posts: 961 | Location: Welcome, MD | Registered: December 06, 1999Reply With QuoteReport This Post



DRR Pro
posted Hide Post
An interesting update. I have decided to scrap the plans for a conventional SB engine. Instead, to move my engine knowledge into the current century, I will be building an LS-series engine. Would you please check back often as we learn how to do a carburated LS drag engine?

More soon as I decide on which block and what size engine.


Larry Woodfin



 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Pro
posted Hide Post
Monte came over today to help layout the wheel tub cuts


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Pro
posted Hide Post
Tub


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Pro
posted Hide Post
And a trial fit of the roll bar


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Pro
posted Hide Post
By tha way, it is an S-10 roll bar that fits the Colorado perfectly


Larry Woodfin



 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Pro
posted Hide Post
In the ballpark


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Pro
posted Hide Post
temporary mock-up


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post



DRR Trophy
Picture of TheBlueTruck
posted Hide Post
Look's good Larry.


Regan Wilson Super Street 469C
 
Posts: 299 | Location: Tyler Texas | Registered: February 24, 2011Reply With QuoteReport This Post
DRR Pro
posted Hide Post
Regan, I expected it to be more reserved, but the fact that I have shortened the wheel base about two inches is obvious. I will relax about it for now and wait until it is on the ground at ride height before passing judgement. The ladder bar crossmember is still just tacked in so I can easily adjust the "look." That is a 29 x 10 tire for mockup and I do plan to run a slightly larger tire.


Larry Woodfin



 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
Mr. Larry,

Why did you shorten it 2" to start with?

also - I have not had any luck with motor core search, still looking.

Ken


KEGRACING - DOING IT THE POOR BOY WAY! PONTIAC with a BowTie... for now!
2017 TX Motorplex No E Track Champion
 
Posts: 21 | Location: Red Oak, TX | Registered: December 01, 1999Reply With QuoteReport This Post
DRR Pro
posted Hide Post
Ken, it was an experiment. I most likey will shuffle the wheel base slighty to best fit the body opening. Too soon to tell just now. Once I have the axles in hand and can bolt everything up it will be a better test. Mocking up with blocks of wood only gives a fellow a rough idea.


Larry Woodfin



 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
Mr. Larry,
Check your email.

Ken


KEGRACING - DOING IT THE POOR BOY WAY! PONTIAC with a BowTie... for now!
2017 TX Motorplex No E Track Champion
 
Posts: 21 | Location: Red Oak, TX | Registered: December 01, 1999Reply With QuoteReport This Post
DRR Pro
posted Hide Post
The "Rado" will be a cool drag truck.


Larry Woodfin





 
Posts: 1872 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2 3 4  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    "Family Tradition" a build for Daughter & Grandchildren

© DragRaceResults.com 2024