Will they clear stock floors, I.e., 3rd gen Fbody floor/ tunnel? Do they leak ? Read some comments about weeping between quick coupling.
You have to put in the effort, to get anything out of it.
October 25, 2020, 10:39 PM
Mike Rietow
quote:
Originally posted by KWig: Will they clear stock floors, I.e., 3rd gen Fbody floor/ tunnel? Do they leak ? Read some comments about weeping between quick coupling.
Definitely not what you want, for what you're doing. You want the best flowing fittings, not the worst.
October 26, 2020, 06:27 AM
SP 124X
We have them and have not experienced any weeping. No 3rd gen fbody experience but ours are not directly on the case we have short hoses then the fittings.
Denis LeBlanc
October 26, 2020, 07:41 AM
RPROGAS
I used them to connect the transmission coolant lines to the cooler, never had a problem even after several years of service. My choice was simple, tightening the coolant line fittings with a wrench in the confined area around them is impossible without removing all the floor panels.
Bob
October 26, 2020, 09:32 AM
seabass
No issues with mine either....
J.R. Baxter
""Fathom the hypocrisy of a Government that requires every citizen to prove they are insured ..but not everyone must prove they are a citizen."
2024 Miller Rolla Competition Engines ProCharger Hoosier Tires Abruzzi
October 26, 2020, 11:06 AM
Lenny5160
I have no experience with them, but I sure think about them a lot while laying under the car with transmission fluid running onto me.
Tony Leonard
October 26, 2020, 11:37 AM
Cashflow
Mine have been on the car for probably 10 years or so. Still working fine, don’t leak. They are a little faded though. As regards the flow, weren’t the original holes in the transmission 1/8 inch pipe?
Clowns to the left of me, Jokers to the right. Here I am.......
October 26, 2020, 07:28 PM
Eman
I've got a 3rd gen with stock floor, but no jiffy Tite. I'd say if I was to use them I would use a short piece of hose then the Jiffy Tite. I used pre-made teflon lines and my lines come up to the frame rail and run along it to the front where y cooler is. I would put the quick disconnects so I could reach them under the hood.
October 26, 2020, 08:02 PM
KWig
Thanks all, I looked under after I got home, I don’t see how there’s enough room, without doing as Eman said. Thanks again !
You have to put in the effort, to get anything out of it.
October 26, 2020, 08:17 PM
seabass
quote:
Originally posted by KWig: Thanks all, I looked under after I got home, I don’t see how there’s enough room, without doing as Eman said. Thanks again !
they have some fittings on hose already, about 12" long
J.R. Baxter
""Fathom the hypocrisy of a Government that requires every citizen to prove they are insured ..but not everyone must prove they are a citizen."
2024 Miller Rolla Competition Engines ProCharger Hoosier Tires Abruzzi
October 26, 2020, 08:41 PM
Bucky
quote:
Originally posted by seabass:
quote:
Originally posted by KWig: Thanks all, I looked under after I got home, I don’t see how there’s enough room, without doing as Eman said. Thanks again !
they have some fittings on hose already, about 12" long
That's what I use
Foxtrot Juliet Bravo
October 26, 2020, 09:23 PM
KWig
Thanks J.R., and Bucky, I’ll look into that.
You have to put in the effort, to get anything out of it.
October 26, 2020, 09:29 PM
Mike Rietow
quote:
Originally posted by Bucky:
quote:
Originally posted by seabass:
quote:
Originally posted by KWig: Thanks all, I looked under after I got home, I don’t see how there’s enough room, without doing as Eman said. Thanks again !
they have some fittings on hose already, about 12" long
That's what I use
Before or after your dump/bypass?
October 26, 2020, 09:46 PM
KWig
I’m one of those crazy foot brake guys....
You have to put in the effort, to get anything out of it.
October 27, 2020, 08:50 AM
Bucky
quote:
Originally posted by Mike Rietow:
quote:
Originally posted by Bucky:
quote:
Originally posted by seabass:
quote:
Originally posted by KWig: Thanks all, I looked under after I got home, I don’t see how there’s enough room, without doing as Eman said. Thanks again !
Tee at the case. External only for now they have some fittings on hose already, about 12" long
That's what I use
Before or after your dump/bypass?
Foxtrot Juliet Bravo
October 27, 2020, 08:51 AM
Bucky
That said... anyone know how to diy an internal dump?
You have to put in the effort, to get anything out of it.
October 27, 2020, 09:16 PM
Mike Rietow
quote:
Originally posted by KWig: Thanks Scott !
Ask your converter guy if it's beneficial to his calculations (stall), he knows you're running jiffy fittings.
October 28, 2020, 08:27 AM
Brktracer
Kwig: I used hard line to get to a more accessible area and then changed to teflon lined braided hose. The hard lines are installed prior to installing the trans and then the connection is in a convenient location - next to the starter on my car. Really no need for quick connects when set up this way. Sent you a pic via text.This message has been edited. Last edited by: Brktracer,
