Bracket Talk
MSD 7765 Wide Band Sensor

This topic can be found at:
https://drr.infopop.cc/eve/forums/a/tpc/f/80760912/m/3807088976

January 23, 2018, 06:30 PM
suprodn
MSD 7765 Wide Band Sensor
What O2 sensor comes in the kit is it a Bosch. I need a extension cable the cable from the module is too short to reach my left O2.
January 23, 2018, 07:11 PM
markemark
quote:
Originally posted by markemark:
quote:
Originally posted by suprodn:
What O2 sensor comes in the kit is it a Bosch. I need a extension cable the cable from the module is too short to reach my left O2.


Another way to do this is to move the CAN-Bus base unit closer to the exhaust so that the O2 sensor reaches. Use these 2’ , 4’, 6’ CAN-Bus extensions MSD 7782, 7784, 7786

January 23, 2018, 07:28 PM
markemark
It’s also possible (not exactly sure) that this cable can also be used between the 7765 and the 7740 CAN-Bus.
January 23, 2018, 08:49 PM
suprodn
I’ve already mounted can-bus hub and both modules on my right door x.
January 23, 2018, 09:55 PM
Stephen Hughes
I was wondering about this too since I just ordered one for my dragster. Ignition box way up front and obviously O2’s way out back...


The Pull-Out....for when you want to work smarter, not harder!!!
January 23, 2018, 10:32 PM
suprodn
Think this may work
https://www.bmotorsports.com/s...-EAQYASABEgIPz_D_BwE
January 24, 2018, 02:32 PM
Alaskaracer
How long are the leads for those? I’m pulling off my LM2 and going to the MSD ones. For my dragster.


Mark Goulette
Owner/Driver of the Livin' The Dream Racing dragster
www.livinthedreamracing.com
"Speed kills but it's better than going slow!"
Authorized Amsoil Retailer
January 24, 2018, 03:17 PM
sr4440
quote:
Originally posted by suprodn:
What O2 sensor comes in the kit is it a Bosch. I need a extension cable the cable from the module is too short to reach my left O2.


the O2 sensor that most use (lm1, lm2, Daytona) is the Bosch LSU 4.2 sensor, msd states that theirs is the LSU 4.9

if your going to add a extension I would use a 4.9 cable. their are measurements on this site to determine which sensor you have.
http://www.innovatemotorsports.com/support/49.php

Joe


Without data, you’re just another guy with an opinion.
January 24, 2018, 04:07 PM
suprodn
quote:
Originally posted by Coloradoracer:
How long are the leads for those? I’m pulling off my LM2 and going to the MSD ones. For my dragster.


They show 12” 24” and 36” in stock and will make custom lengths also
January 24, 2018, 04:43 PM
CHampshire
Daytona Sensors made me two custom length extensions for my Wego. If I remember correctly one was 91" and the other was 105. Both of them to the door cost me 35 bucks total. May be worth a phone call.
April 10, 2018, 01:38 PM
RacerVX54
Anyone have any issues? Installed mine on the grid and i am getting a red blinking light. Heater open fault as soon as it the pc starts up with the program.. Called wonderful MSD and got hey techs are in the other building we can call you back tomorrow... And i was speaking to a tech line guy!! SMH


"Just Shut Up and Race"

Brian Martin
Martin Racing
5.66 @121.55
April 10, 2018, 02:41 PM
markemark
quote:
Originally posted by RacerVX54:
Anyone have any issues? Installed mine on the grid and i am getting a red blinking light. Heater open fault as soon as it the pc starts up with the program.


Is the Red wire from the O2 Sensor Module connected to a “Continuous” +12v battery source?
April 10, 2018, 03:02 PM
RacerVX54
quote:
Originally posted by markemark:
quote:
Originally posted by RacerVX54:
Anyone have any issues? Installed mine on the grid and i am getting a red blinking light. Heater open fault as soon as it the pc starts up with the program.


Is the Red wire from the O2 Sensor Module connected to a “Continuous” +12v battery source?


Not sure pops wired it up. I do know the o2
only comes on when the ignition switch it on


"Just Shut Up and Race"

Brian Martin
Martin Racing
5.66 @121.55
April 10, 2018, 03:46 PM
markemark
quote:
Originally posted by RacerVX54:
quote:
Originally posted by markemark:
quote:
Originally posted by RacerVX54:
Anyone have any issues? Installed mine on the grid and i am getting a red blinking light. Heater open fault as soon as it the pc starts up with the program.


Is the Red wire from the O2 Sensor Module connected to a “Continuous” +12v battery source?


Not sure pops wired it up. I do know the o2
only comes on when the ignition switch it on


Turning ignition switch ON to Grid turns the modules on attached to the CAN-bus hub for communication..

Select 7765 in Grid and go to the Gauge 1 tab. Select the Battery Voltage and Heater Voltage channels. What do they indicate?
April 10, 2018, 04:45 PM
RacerVX54
Battery voltage is 12.6 off and car running was 13.8 I o2 read 6.4 and but it wouldn't change like it didn't read. As soon as you select the o2 setting the heater open fault would pop on. Clear it and come right back on.

This message has been edited. Last edited by: RacerVX54,


"Just Shut Up and Race"

Brian Martin
Martin Racing
5.66 @121.55
April 10, 2018, 05:56 PM
markemark
quote:
Originally posted by RacerVX54:
Battery voltage is 12.6 off and car running was 13.8 I o2 read 6.4 and but it wouldn't change like it didn't read. As soon as you select the o2 setting the heater open fault would pop on. Clear it and come right back on.


What does the “Heater Voltage “ channel display for voltage ?
April 10, 2018, 06:36 PM
RacerVX54
Mark i am not sure i will check that in the morning.


"Just Shut Up and Race"

Brian Martin
Martin Racing
5.66 @121.55
April 10, 2018, 06:49 PM
markemark
quote:
Originally posted by RacerVX54:
Mark i am not sure i will check that in the morning.


Prior to starting, unplug the Oxygen Sensor from the O2 sensor Module and look at the pins (qty 6 ) in the plug ends to see if they all look the same for position. If good, then re-seat plugs and try viewing the Heater Voltage. No work, call MSD. They’ll ask you some of the same questions.
April 10, 2018, 07:08 PM
RacerVX54
Thanks will do


"Just Shut Up and Race"

Brian Martin
Martin Racing
5.66 @121.55
April 11, 2018, 11:51 AM
RacerVX54
Heater voltage is 0.00


"Just Shut Up and Race"

Brian Martin
Martin Racing
5.66 @121.55