MSD 7765 Wide Band Sensor

DRR Sportsman

posted

What O2 sensor comes in the kit is it a Bosch. I need a extension cable the cable from the module is too short to reach my left O2.

Posts: 63 | Location: Watchn my motor go boom on the dyno | Registered: April 04, 2009

DRR Pro

posted

quote:
Originally posted by markemark:
quote:
Originally posted by suprodn:
What O2 sensor comes in the kit is it a Bosch. I need a extension cable the cable from the module is too short to reach my left O2.

Another way to do this is to move the CAN-Bus base unit closer to the exhaust so that the O2 sensor reaches. Use these 2’ , 4’, 6’ CAN-Bus extensions MSD 7782, 7784, 7786

Posts: 2697 | Location: 53056 | Registered: December 30, 2009

Ignored post by markemark posted

DRR Pro

posted

It’s also possible (not exactly sure) that this cable can also be used between the 7765 and the 7740 CAN-Bus.

Posts: 2697 | Location: 53056 | Registered: December 30, 2009

Ignored post by markemark posted

DRR Sportsman

posted

I’ve already mounted can-bus hub and both modules on my right door x.

Posts: 63 | Location: Watchn my motor go boom on the dyno | Registered: April 04, 2009

Ignored post by suprodn posted

Stephen Hughes

DRR Sportsman

posted

I was wondering about this too since I just ordered one for my dragster. Ignition box way up front and obviously O2’s way out back...

The Pull-Out....for when you want to work smarter, not harder!!!

Posts: 337 | Location: Texas | Registered: September 12, 2005

Ignored post by Stephen Hughes posted

DRR Sportsman

posted

Think this may work
https://www.bmotorsports.com/s...-EAQYASABEgIPz_D_BwE

Posts: 63 | Location: Watchn my motor go boom on the dyno | Registered: April 04, 2009

Ignored post by suprodn posted

Alaskaracer

DRR Pro

posted

How long are the leads for those? I’m pulling off my LM2 and going to the MSD ones. For my dragster.

Mark Goulette
Owner/Driver of the Livin' The Dream Racing dragster
www.livinthedreamracing.com
"Speed kills but it's better than going slow!"
Authorized Amsoil Retailer

Posts: 1545 | Location: Back home in Alaska! | Registered: February 13, 2011

Ignored post by Alaskaracer posted

sr4440

DRR Sportsman

posted

quote:
Originally posted by suprodn:
What O2 sensor comes in the kit is it a Bosch. I need a extension cable the cable from the module is too short to reach my left O2.

the O2 sensor that most use (lm1, lm2, Daytona) is the Bosch LSU 4.2 sensor, msd states that theirs is the LSU 4.9

if your going to add a extension I would use a 4.9 cable. their are measurements on this site to determine which sensor you have.
http://www.innovatemotorsports.com/support/49.php

Joe

Without data, you’re just another guy with an opinion.

Posts: 1313 | Location: TEXAS | Registered: February 07, 2003

Ignored post by sr4440 posted

DRR Sportsman

posted

quote:
Originally posted by Coloradoracer:
How long are the leads for those? I’m pulling off my LM2 and going to the MSD ones. For my dragster.

They show 12” 24” and 36” in stock and will make custom lengths also

Posts: 63 | Location: Watchn my motor go boom on the dyno | Registered: April 04, 2009

Ignored post by suprodn posted

CHampshire

DRR Trophy

posted

Daytona Sensors made me two custom length extensions for my Wego. If I remember correctly one was 91" and the other was 105. Both of them to the door cost me 35 bucks total. May be worth a phone call.

Posts: 97 | Location: Ohio | Registered: October 06, 2015

Ignored post by CHampshire posted

DRR Pro

posted

Anyone have any issues? Installed mine on the grid and i am getting a red blinking light. Heater open fault as soon as it the pc starts up with the program.. Called wonderful MSD and got hey techs are in the other building we can call you back tomorrow... And i was speaking to a tech line guy!! SMH

"Just Shut Up and Race"

Brian Martin
Martin Racing
5.50 126

Posts: 1422 | Location: Va.Beach .Va | Registered: August 03, 2005

Ignored post by RacerVX54 posted

DRR Pro

posted

quote:
Originally posted by RacerVX54:
Anyone have any issues? Installed mine on the grid and i am getting a red blinking light. Heater open fault as soon as it the pc starts up with the program.

Is the Red wire from the O2 Sensor Module connected to a “Continuous” +12v battery source?

Posts: 2697 | Location: 53056 | Registered: December 30, 2009

Ignored post by markemark posted

DRR Pro

posted

quote:
Originally posted by markemark:
quote:
Originally posted by RacerVX54:
Anyone have any issues? Installed mine on the grid and i am getting a red blinking light. Heater open fault as soon as it the pc starts up with the program.

Is the Red wire from the O2 Sensor Module connected to a “Continuous” +12v battery source?

Not sure pops wired it up. I do know the o2
only comes on when the ignition switch it on

"Just Shut Up and Race"

Brian Martin
Martin Racing
5.50 126

Posts: 1422 | Location: Va.Beach .Va | Registered: August 03, 2005

Ignored post by RacerVX54 posted

DRR Pro

posted

quote:
Originally posted by RacerVX54:
quote:
Originally posted by markemark:
quote:
Originally posted by RacerVX54:
Anyone have any issues? Installed mine on the grid and i am getting a red blinking light. Heater open fault as soon as it the pc starts up with the program.

Is the Red wire from the O2 Sensor Module connected to a “Continuous” +12v battery source?

Not sure pops wired it up. I do know the o2
only comes on when the ignition switch it on

Turning ignition switch ON to Grid turns the modules on attached to the CAN-bus hub for communication..

Select 7765 in Grid and go to the Gauge 1 tab. Select the Battery Voltage and Heater Voltage channels. What do they indicate?

Posts: 2697 | Location: 53056 | Registered: December 30, 2009

Ignored post by markemark posted

DRR Pro

posted

Battery voltage is 12.6 off and car running was 13.8 I o2 read 6.4 and but it wouldn't change like it didn't read. As soon as you select the o2 setting the heater open fault would pop on. Clear it and come right back on.

This message has been edited. Last edited by: RacerVX54,

"Just Shut Up and Race"

Brian Martin
Martin Racing
5.50 126

Posts: 1422 | Location: Va.Beach .Va | Registered: August 03, 2005

Ignored post by RacerVX54 posted

DRR Pro

posted

quote:
Originally posted by RacerVX54:
Battery voltage is 12.6 off and car running was 13.8 I o2 read 6.4 and but it wouldn't change like it didn't read. As soon as you select the o2 setting the heater open fault would pop on. Clear it and come right back on.

What does the “Heater Voltage “ channel display for voltage ?

Posts: 2697 | Location: 53056 | Registered: December 30, 2009

Ignored post by markemark posted

DRR Pro

posted

Mark i am not sure i will check that in the morning.

"Just Shut Up and Race"

Brian Martin
Martin Racing
5.50 126

Posts: 1422 | Location: Va.Beach .Va | Registered: August 03, 2005

Ignored post by RacerVX54 posted

DRR Pro

posted

quote:
Originally posted by RacerVX54:
Mark i am not sure i will check that in the morning.

Prior to starting, unplug the Oxygen Sensor from the O2 sensor Module and look at the pins (qty 6 ) in the plug ends to see if they all look the same for position. If good, then re-seat plugs and try viewing the Heater Voltage. No work, call MSD. They’ll ask you some of the same questions.

Posts: 2697 | Location: 53056 | Registered: December 30, 2009

Ignored post by markemark posted

DRR Pro

posted

Thanks will do

"Just Shut Up and Race"

Brian Martin
Martin Racing
5.50 126

Posts: 1422 | Location: Va.Beach .Va | Registered: August 03, 2005

Ignored post by RacerVX54 posted

DRR Pro

posted

Heater voltage is 0.00

"Just Shut Up and Race"

Brian Martin
Martin Racing
5.50 126

Posts: 1422 | Location: Va.Beach .Va | Registered: August 03, 2005

Ignored post by RacerVX54 posted