DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  General Discussion - by FTI    rusty engine blocks
Go
New
Find
Notify
Tools
Reply
  
rusty engine blocks
 Login/Join
 
DRR Trophy
Picture of BTR69
posted
Good evening. I just became the owner of 2 old sbc blocks, (freebies). one has crank, rods and pistons still. They've been outside for a few years and look like good candidates for boat anchors. I'm curious if it would be worth a try, to clean them up and possibly use them. What would be the best somewhat low buck way to try to clean them up? Thanks.


William Kilduff
1970 Barracuda
1968 Camaro X2
1968 Caprice
1964 F100
 
Posts: 179 | Location: Wilmington NC | Registered: June 15, 2014Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
Many shops (out west anyways) have a "bake and blast" procedure that they put the block in an oven for a while (usually to burn off the grease and oil) then put it in shot peening machine that gets the block down to bare metal/new looking... it used to be a hundred dollar job but that was several years ago since I had one done...
Other than that is acid dipping which California has pretty much banned from existence out here


.
Dave



F J B

 
Posts: 4635 | Location: Earth | Registered: February 08, 2006Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
A DIY electrolysis tank works wonders on cast iron.

A few days in a tub of water with a 12-volt battery charger and a piece of sacrificial metal....

https://realtree.com/timber-2-...nWIMXi7-o8C8taj7aXDU
 
Posts: 131 | Location: Imperial, CA | Registered: September 12, 2013Reply With QuoteReport This Post
DRR S/Pro
Picture of David Covey
posted Hide Post
quote:
Originally posted by fivecentcharlie:
A DIY electrolysis tank works wonders on cast iron.

A few days in a tub of water with a 12-volt battery charger and a piece of sacrificial metal....

https://realtree.com/timber-2-...nWIMXi7-o8C8taj7aXDU


I've done this and it works OK to get most of the rust off it will not degrease it though. But would still need to be cleaned at a machine shop before using it.
I have also used vinegar and molasses to clean sheet metal when restoring body panels on my old ford.
Dave.


"It is usually futile to try to talk facts and analysis to people who are enjoying a sense of moral superiority in their ignorance." -Thomas Sowell
 
Posts: 3421 | Location: American By Birth Texan By The Grace Of God  | Registered: April 29, 2004Reply With QuoteReport This Post
DRR Pro
Picture of SlyFox
posted Hide Post
I was gifted (free) a 454 block and a set of 781 heads many years ago. They looked like they had been stored under water - really rusty. After letting them take up space under my work bench for several more years, I decided to either use them or get rid of them, and took them to a machine shop. To my surprise, the block cleaned up nicely at .060 over, and the heads likewise were refreshed with larger 2.19/1.88 valves and new springs, retainers, locks, etc.

Stroked to 496 with a new rotating assembly, I had a low-buck street/strip engine that made hundreds of 11.50 passes in a 4,000lb Chevelle. After 8 years of that, I sold the car to a buddy and he is still driving it. He disassembled the motor with intentions to refresh it, and it all looked so good he just put it back together with the original rings, bearings, etc.

The crusty looking stuff can still have a surprising amount of life left in it.


Mike
 
Posts: 1620 | Location: Marietta, GA | Registered: December 09, 2005Reply With QuoteReport This Post
DRR Sportsman
Picture of FastLane
posted Hide Post
 
Posts: 410 | Location: Parked... | Registered: May 27, 2007Reply With QuoteReport This Post
DRR Trophy
Picture of BTR69
posted Hide Post
Thanks y'all. I'm feeling more optimistic about these now. Hoping to get started de-rusting one of them soon. Hope to remember to document how it goes and update with results.


William Kilduff
1970 Barracuda
1968 Camaro X2
1968 Caprice
1964 F100
 
Posts: 179 | Location: Wilmington NC | Registered: June 15, 2014Reply With QuoteReport This Post



  Powered by Social Strata  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  General Discussion - by FTI    rusty engine blocks

© DragRaceResults.com 2025