Go
New
Find
Notify
Tools
Reply
  
Trailer trim?
 Login/Join
 
DRR Pro
Picture of Bruce Williams
posted
I'm adding a couple of doors into the gooseneck of my race car trailer.
I'm unable to find a supplier of aluminum trim for my project.
I'm looking for some 1" flat on 1 side with beveled edges.
Second is 1/2" angle that is flat on outside with rounded edges for drip rail around door edge.
Any ideas? Google seems to show every thing but hat I'm looking for,


Bruce Lee Cool

Experience is what you get when you don't get what you want.
 
Posts: 2062 | Location: Chandler Arizona | Registered: August 11, 2005Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
WAG..... Grainger?


Illegitimi non carborundum
 
Posts: 2367 | Location: OKC, OK | Registered: February 15, 2008Reply With QuoteReport This Post
DRR S/Pro
Picture of CURTIS REED
posted Hide Post
Bruce, I am not sure I understand exactly what you are describing to help you look.


One suggestion is McMaster-Carr though.



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 3138 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
DRR Pro
Picture of Bruce Williams
posted Hide Post

Looking for the bottom piece with the bevel. Approximately 1 3/8" wide





Angle piece is 7/8 X 5/8


Bruce Lee Cool

Experience is what you get when you don't get what you want.
 
Posts: 2062 | Location: Chandler Arizona | Registered: August 11, 2005Reply With QuoteReport This Post
DRR S/Pro
Picture of CURTIS REED
posted Hide Post
Gotcha.
How thick is the 1 3/8" piece?

I will do some looking. The angle looks to be a special extrusion.



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 3138 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
DRR S/Pro
Picture of CURTIS REED
posted Hide Post
Here is one part.

https://eagle-aluminum.com/pro...inum-cove-1316-x-58/

Same place has 1" that looks nice but not exact, I don't see 1 3/8"

https://eagle-aluminum.com/pro...l-1-x-316-half-oval/

This message has been edited. Last edited by: CURTIS REED,



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 3138 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
DRR Top Comp
Picture of wideopen231
posted Hide Post
Wish I could help you out,but I am having a similar problem finding extrusions for building cpl cabinets. You would think with all the stuff everyone can find on the internet it would be easier to find this stuff.

This message has been edited. Last edited by: wideopen231,




America home of free. Brought to you by 2nd amendment.
 
Posts: 4501 | Location: Greensboro NC | Registered: May 24, 2011Reply With QuoteReport This Post



DRR Pro
Picture of Bruce Williams
posted Hide Post
quote:
Originally posted by CURTIS REED:
Here is one part.

https://eagle-aluminum.com/pro...inum-cove-1316-x-58/

Same place has 1" that looks nice but not exact, I don't see 1 3/8"

https://eagle-aluminum.com/pro...l-1-x-316-half-oval/


Curtis I found this sight ^^ after I my original post. The beveled part I have found no where. Might have to go with the curved piece.
The beveled piece is approximately 1/8" thick
Thanks again


Bruce Lee Cool

Experience is what you get when you don't get what you want.
 
Posts: 2062 | Location: Chandler Arizona | Registered: August 11, 2005Reply With QuoteReport This Post
  Powered by Social Strata  
 


© DragRaceResults.com 2024