DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    part number on 12 point 12 degree profilers head studs
Go
New
Find
Notify
Tools
Reply
  
part number on 12 point 12 degree profilers head studs
 Login/Join
 
td9757
DRR Trophy
posted
part number on 12 point 12 degree profilers head studs. block is merlin tall deck 598 if that matters
 
Posts: 30 | Location: tennessee | Registered: November 29, 2008Reply With QuoteReport This Post
TOP38
DRR S/Pro
posted Hide Post
Call Profiler or ARP for a kit number.
 
Posts: 2163 | Location: Tewksbury, MA,USA | Registered: November 03, 2000Reply With QuoteReport This Post
Kenneth
DRR Trophy
posted Hide Post
Call Reher-Morrison.


Abbott Racing Heads
(432) 558-2841
 
Posts: 40 | Location: Crane, Texas | Registered: January 12, 2009Reply With QuoteReport This Post
Alaskaracer
DRR Pro
Picture of Alaskaracer
posted Hide Post
quote:
Originally posted by Kenneth:
Call Reher-Morrison.


^^This. ARP doesn't make a stud kit for these heads. The kit from Reher will also have the proper undersize washers to fit in the counter bores for the stud nuts. Regular washers won't fit.


Mark Goulette
Owner/Driver of the Livin' The Dream Racing dragster
www.livinthedreamracing.com
"Speed kills but it's better than going slow!"
Authorized Amsoil Retailer
 
Posts: 1545 | Location: Back home in Alaska! | Registered: February 13, 2011Reply With QuoteReport This Post
TOP38
DRR S/Pro
posted Hide Post
quote:
Originally posted by Coloradoracer:
quote:
Originally posted by Kenneth:
Call Reher-Morrison.


^^This. ARP doesn't make a stud kit for these heads. The kit from Reher will also have the proper undersize washers to fit in the counter bores for the stud nuts. Regular washers won't fit.


With all the different heads out there that makes sense but it's not rocket science. There are only two holes per head that need a small diameter washer, easy enough to do some customer adjusting.
 
Posts: 2163 | Location: Tewksbury, MA,USA | Registered: November 03, 2000Reply With QuoteReport This Post
td9757
DRR Trophy
posted Hide Post
maybe my problem of the engine builder used the wrong washers cause some are tight in the pocket and some studs look like they was modified or cut off
 
Posts: 30 | Location: tennessee | Registered: November 29, 2008Reply With QuoteReport This Post
Will Harrison
DRR S/Pro
posted Hide Post
quote:
Originally posted by TOP38:
quote:
Originally posted by Coloradoracer:
quote:
Originally posted by Kenneth:
Call Reher-Morrison.


^^This. ARP doesn't make a stud kit for these heads. The kit from Reher will also have the proper undersize washers to fit in the counter bores for the stud nuts. Regular washers won't fit.


With all the different heads out there that makes sense but it's not rocket science. There are only two holes per head that need a small diameter washer, easy enough to do some customer adjusting.
yup, wasn't that big of a deal to cut down 4 washers. Other then the 4 washers the kit from ARP works perfect.


.991 60'
4.36 @ 159 so far.....
6.86 @ 198 trying for more......

533" single carb
235" Harrison 4-link
 
Posts: 1087 | Location: Nova Siri, Italy | Registered: June 03, 2009Reply With QuoteReport This Post



  Powered by Social Strata  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    part number on 12 point 12 degree profilers head studs

© DragRaceResults.com 2024