Bracket Talk
Engine heater

This topic can be found at:
https://drr.infopop.cc/eve/forums/a/tpc/f/80760912/m/7227049496

November 25, 2020, 05:18 PM
Larry Woodfin
Engine heater
I have looked at the elements that bolt in a core plug h o l e, but I'm not too fond of the fit. What other options are available?

I "think" I want a heater that will install inline the lower hose. NOTE, I have a #12 AN lower hose.


Larry Woodfin



November 25, 2020, 06:38 PM
CURTIS REED
Larry, do you have an aluminum radiator? If so you can weld a fitting in it and use a screw in heater element. That’s what I did. I used a Kay’s brand heater.



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
November 25, 2020, 06:46 PM
FastLane
What about the oil pan heater?
November 25, 2020, 07:04 PM
Bucky
I like the oil heaters and use them. I have considered water heaters, but my concern is anything that could push out and cause a dangerous condition. A screw in heater for the radiator would be good, but wouldn't heat the block until you circulate the water.


Foxtrot Juliet Bravo
November 25, 2020, 08:24 PM
CURTIS REED
I also use an oil heater.



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
November 25, 2020, 08:26 PM
1320racer
don't see any need or benefit for what we do.
November 25, 2020, 08:59 PM
seabass
https://www.hotheadheater.com/


J.R. Baxter

""Fathom the hypocrisy of a Government that requires every citizen to prove they are insured ..but not everyone must prove they are a citizen."

2025 Miller
Rolla Competition Engines
ProCharger
Hoosier Tires
Abruzzi
November 25, 2020, 09:13 PM
BG7X77
I always get a little nervous on those cold morning would he a useful option to have. Oil heater has almost zero weight, seems like all upside and no down side to me. Why not start your motor with nice warm oil.


BG
November 25, 2020, 09:15 PM
Larry Woodfin
JR, at $1399.00 me and Jef will both get one.


Larry Woodfin



November 25, 2020, 09:22 PM
seabass
thats why i havent yet but they have cheaper models, a little cheaper


J.R. Baxter

""Fathom the hypocrisy of a Government that requires every citizen to prove they are insured ..but not everyone must prove they are a citizen."

2025 Miller
Rolla Competition Engines
ProCharger
Hoosier Tires
Abruzzi
November 26, 2020, 09:12 AM
markemark
quote:
Originally posted by 1320racer:
don't see any need or benefit for what we do.


^^^^^ Agreed!!
November 26, 2020, 11:58 AM
Goob
Lower hose heater will circulate.
There's also a heater that connects to the radiator drain and a heater hose, it circulates well. Kats Engine Heaters.

There's more damage done to race engines with improper warm up than any other cause, I'll fight you on that.

It's nice also to roll in with the oil hot when you have to buy into 2nd round....just saying, I've seen that happen. Wink


"Despite the high cost of living, it remains popular."
Dave Cook
N375
November 26, 2020, 12:40 PM
green1
I have one soft plug heater on each side and put a little right stuff on them before installation and they aren’t gonna push out. It saves a ton of fuel when you are at track a couple hours early or over night and can warm up the motor to 160 with just a gallon or so of regular fuel. I had one go bad and had to pry it out of the block after loosening the screw.
November 26, 2020, 02:32 PM
adv ET 266
I used a pair (one in each side) in the last 3 BBC’s I built. Never and issue and didn’t have to run the water pump.
Guess it may depend on the manufacture as far as fit quality.



2005 2000lb 4 link dragster
home brew 582 BBC Dart 355
1.058
2.98
4.629@149
6.094
7.310@185

November 26, 2020, 10:22 PM
Eman
https://katsblockheater.com/
All of the heaters you want
December 01, 2020, 11:16 PM
Steve from Pa
We have a in-line water heater in the bottom Rad hose, and 600W moroso pad heater on the bottom of the oil pan, and am changing to a sheet metal pan on the tranny so I can add a pad heater on the tranny this winter.

I like having fluid temps where I want them. I think I was burning more fuel trying to the temps I wanted than racing, The heaters really cut your alcohol use down.


Most important, keep the shiny side up
December 02, 2020, 07:14 AM
WHOMPWHOMP
Anybody make a inline with -AN fittings....
December 02, 2020, 09:08 AM
TOP38
For those with AL blocks, Jegs sells a block heater with the adapter to thread into the block.

As for water heaters required or not, it certainly doesn't hurt to have one and will save some warmup fuel. There are combo's that do require them, specifically motors with AL blocks and tight lash cams, on a cold morning the so called closed valves will actually be open a bit until the block is warmed up. I run an Brodix AL block with a regular lash cam, (.022 hot) and on a cold morning the lash will be between .004 to .006 so it doesn't take much to have the rockers actually hold the closed valves open once you get a cam with less than .018 hot lash.

Living in the northeast, I installed one and use it during the early spring and late fall when the car is still in the trailer if the night time temps fall well below freezing. I plug the block heater in for a few hours after diner and wrap the motor up with blankets which works well. (No antifreeze in my race motor!)