Page 1 2 3 
Go
New
Find
Notify
Tools
Reply
  
Alternator
 Login/Join
 
DRR Sportsman
posted
What alternator are people running these days?
 
Posts: 863 | Location: Georgia | Registered: May 09, 2008Reply With QuoteReport This Post
DRR Pro
posted Hide Post
For most of my SBC builds I install a common auto parts store alternator. Select an alternator of 80 - 100-amp rating. In some situations, a factory mounting will work, in other situations a custom mounting will be built. It will be wired just as if it were an OE install. I see no reason to do otherwise. One thing of importance, select pulleys that limit the alternator speed. Spinning the alternator approximately engine speed is completely sufficient.


Larry Woodfin



 
Posts: 1871 | Location: Kilgore TX | Registered: March 12, 2004Reply With QuoteReport This Post
DRR Trophy
Picture of Rodney Pryor
posted Hide Post
House of Payne
 
Posts: 127 | Location: Richmond, VA | Registered: December 07, 2002Reply With QuoteReport This Post
DRR Elite
posted Hide Post
#2005 16volt 120amp from East Coast Alternators in both cars
 
Posts: 13522 | Location: NJ | Registered: August 20, 2000Reply With QuoteReport This Post
DRR Trophy
Picture of Little Chief
posted Hide Post
My wife bought me a 16 volt super mini from HOP 2 years ago for Christmas. It's a quality piece of equipment and does the job well.
 
Posts: 241 | Location: Kilgore Texas | Registered: July 15, 2019Reply With QuoteReport This Post
DRR Pro
posted Hide Post
I use one 12v battery and never charge when at the track………… NEVER!

 
Posts: 2671 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post
DRR Top Comp
Picture of Curly1
posted Hide Post
PM sent.


https://postimg.cc/gallery/np3zpruo/
"Dunning-Kruger Effect"
-a type of Cognitive bias where people with little expertise or ability assume they have superior expertise or ability. This overestimation occurs as a result of the fact that they do not have enough knowledge to know they don't have enough knowledge.

Before you argue with someone ask yourself, "Is this person mentally mature enough to grasp the concept of a different perspective?" If not there is no point to argue.

4X NE2 CHAMPION. 2020 TDRA NE2 Champion
 
Posts: 4278 | Location: United States of Texas | Registered: April 02, 2011Reply With QuoteReport This Post



DRR Top Comp
posted Hide Post
East Coast Ultra Mini 16 volt on mine. Seems to work okay. I put the maintainer on it at the track but lately it seems I can't get past first round so no real reason. LOL


Clowns to the left of me, Jokers to the right. Here I am.......
 
Posts: 5334 | Location: stuck in the middle with you! | Registered: March 11, 2002Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
If you have a 12 volt system I like an oem gm alternators. Easy to wire in and also easy to find a replacement if needed. As Larry said watch pulley ratio so you don’t over speed the alternator. If on a 16 volt system then I would probably go with house of Payne.
 
Posts: 516 | Location: Going to or returning from the chipmine. | Registered: July 01, 2011Reply With QuoteReport This Post
DRR Pro
posted Hide Post
quote:
One thing of importance, select pulleys that limit the alternator speed. Spinning the alternator approximately engine speed is completely sufficient.


Good advice for a circle track car. For drag racing I use 2 to 1 which I believe is a better choice.

Some engines idle very low which can limit the alternator output. My engine idles 1400 rpm both in neutral, as well as in gear. I use 2 gauge charging wire.

Power Master site says their alternators will take up to 20,000 rpm for short periods.
 
Posts: 2671 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post
DRR Sportsman
Picture of TomR
posted Hide Post
My old single wire alt couldn't keep up with the demands and the car was inconsistent. Once I installed a grid, I could see the alternator struggling to reach 12v after the shift. It would actually drop to 10v and barely make it back to 12v by the end of the run.

I installed a 100amp Powermaster single wire alt and it straightened out the problem.


72 Nova "Hooptie"
 
Posts: 791 | Location: Hanover, MD | Registered: June 20, 2016Reply With QuoteReport This Post
DRR S/Pro
Picture of Eman
posted Hide Post
I've had a Powermaster alternator with the low mount aluminum bracket and pulley on my car for over 20 years. It works fine, had to have a regulator replaced once at a local shop. Keep a spare belt but have never needed it. Have a volt gauge on the dahs so I can see it's working. 12V simple and reliable.
 
Posts: 1568 | Location: E TN | Registered: February 13, 2009Reply With QuoteReport This Post
DRR Pro
Picture of 67TSCHEVY2
posted Hide Post
east coast 16 with their crank pulley
 
Posts: 1259 | Location: middle georgia | Registered: July 20, 2003Reply With QuoteReport This Post
DRR Pro
Picture of Goob
posted Hide Post
Running the alternator my car was delivered with new, 63 amp Delcotron, 1-wire converted, running 1:1 pulley ratio, with a single Group 31 battery.
It's adequate.


"Despite the high cost of living, it remains popular."
Dave Cook
N375
 
Posts: 1831 | Location: Indy | Registered: November 21, 2008Reply With QuoteReport This Post



DRR Pro
posted Hide Post
Get the biggest alternator you can fit. Wont hurt anything


--------------------
Bob Payton
S/P, T/D, S/C, TOP
309Z, 393, 3093, 8X93


www.apdracing.com
www.diamondracecars.com
www.callies.com
 
Posts: 1996 | Location: Michigan | Registered: November 14, 2001Reply With QuoteReport This Post
DRR Sportsman
Picture of gd31
posted Hide Post
If using a high amp alternator be sure to use at least a 2ga wire. The 10ga wire that came with the switch panel wiring kit come to find out wasn't big enough Mad




 
Posts: 600 | Location: Greenwood Indiana | Registered: November 16, 2000Reply With QuoteReport This Post
DRR Pro
posted Hide Post
quote:
If using a high amp alternator be sure to use at least a 2ga wire


Agreed on the 2 gauge minimum. If tying the alternator wire to the starter (my preferred method) using the same size wire on alternator as battery to starter is a wise choice.
 
Posts: 2671 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
quote:
Originally posted by markemark:
quote:
If using a high amp alternator be sure to use at least a 2ga wire


Agreed on the 2 gauge minimum. If tying the alternator wire to the starter (my preferred method) using the same size wire on alternator as battery to starter is a wise choice.


Agreed!
One of the most common errors on race cars.


BG
 
Posts: 760 | Location: Florence, SC | Registered: August 25, 2019Reply With QuoteReport This Post
DRR S/Pro
Picture of Eman
posted Hide Post
People must have some rockin stereos in their cars to need all of that amperage.
 
Posts: 1568 | Location: E TN | Registered: February 13, 2009Reply With QuoteReport This Post
DRR S/Pro
Picture of CURTIS REED
posted Hide Post
quote:
Originally posted by Eman:
People must have some rockin stereos in their cars to need all of that amperage.


Agreed. LOL



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 3143 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2 3  
 


© DragRaceResults.com 2024