DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Lateral trans to rear alignment
Go
New
Find
Notify
Tools
Reply
  
Lateral trans to rear alignment
 Login/Join
 
DRR Sportsman
Picture of Ron Gusack
posted
Just put the trans back in and I have to have the trans mount slid way over to get the bolts through the crossmember and into the mount. I've seen homemade tools using a laser pointer to align the pinion center with the output shaft. Is there a laser tool available to do this?
 
Posts: 465 | Location: Maryland | Registered: January 23, 2007Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
I JB welded a round magnet to one of these

https://www.amazon.com/GOTICAL...%2Caps%2C212&sr=8-15

and put it on the tail shaft of the transmission..
 
Posts: 108 | Location: upstate NY | Registered: January 15, 2018Reply With QuoteReport This Post
DRR S/Pro
Picture of "The Bender"
posted Hide Post
quote:
Originally posted by 69427:
I JB welded a round magnet to one of these

https://www.amazon.com/GOTICAL...%2Caps%2C212&sr=8-15

and put it on the tail shaft of the transmission..


Good idea, but wouldn't it point below the pinion if the tailshaft in angled down like most stock chassis cars?


272" Spitzer
540 Chevy
The Blower Shop XR1
FTI XPM Series Converter
FTI Level 6 Powerglide
3.69@199
.916 60'

2017 Bradenton Heads Up Madness
Open Outlaw Champ

2018 PDRA T/D #5
2019 PDRA T/D #2

2020 Retired From T/D Competition....

2020 Bradenton NMCA Hemi Shootout Winner

2021 getting back into bracket racing with a Gen3 Hemi powered 87 Cutlass.
 
Posts: 3103 | Location: Yes | Registered: July 08, 2009Reply With QuoteReport This Post
DRR Sportsman
Picture of Ron Gusack
posted Hide Post
quote:
Originally posted by 69427:
I JB welded a round magnet to one of these

https://www.amazon.com/GOTICAL...%2Caps%2C212&sr=8-15

and put it on the tail shaft of the transmission..

I've heard of guys using a magnet on the pinion and then rotate the tires to get the laser to not draw a circle up near the trans. Once the laser stays as a dot when rotated, your dead on. Here's a Youtube homemade tool but I like yours better. https://www.youtube.com/watch?v=RBYaAkQMSE0

This message has been edited. Last edited by: Ron Gusack,
 
Posts: 465 | Location: Maryland | Registered: January 23, 2007Reply With QuoteReport This Post
DRR Pro
Picture of rusty
posted Hide Post
why is it different


honesty is the best policy,insanity is a better deffense
1.036, 6.16@ 224

 
Posts: 1468 | Location: texas | Registered: February 17, 2006Reply With QuoteReport This Post
DRR Sportsman
Picture of Ron Gusack
posted Hide Post
I'm not sure if it is, but I've never checked it and I've moved the rear a little to equalize the slick to quarter distance. The trans mount is slid way off center compared to the tailshaft so it looks weird. I guess it's just a peace of mind thing.
 
Posts: 465 | Location: Maryland | Registered: January 23, 2007Reply With QuoteReport This Post
DRR S/Pro
Picture of "The Bender"
posted Hide Post
Is this a stock chassis car?


272" Spitzer
540 Chevy
The Blower Shop XR1
FTI XPM Series Converter
FTI Level 6 Powerglide
3.69@199
.916 60'

2017 Bradenton Heads Up Madness
Open Outlaw Champ

2018 PDRA T/D #5
2019 PDRA T/D #2

2020 Retired From T/D Competition....

2020 Bradenton NMCA Hemi Shootout Winner

2021 getting back into bracket racing with a Gen3 Hemi powered 87 Cutlass.
 
Posts: 3103 | Location: Yes | Registered: July 08, 2009Reply With QuoteReport This Post



DRR Sportsman
Picture of Ron Gusack
posted Hide Post
70 Nova with the OEM front subframe and SRD frame rails to the back. Originally we used leaf springs with the slider box that SRD built. She's old,
 
Posts: 465 | Location: Maryland | Registered: January 23, 2007Reply With QuoteReport This Post
DRR S/Pro
Picture of "The Bender"
posted Hide Post
Did you change the transmission crossmember or motor mounts recently?


272" Spitzer
540 Chevy
The Blower Shop XR1
FTI XPM Series Converter
FTI Level 6 Powerglide
3.69@199
.916 60'

2017 Bradenton Heads Up Madness
Open Outlaw Champ

2018 PDRA T/D #5
2019 PDRA T/D #2

2020 Retired From T/D Competition....

2020 Bradenton NMCA Hemi Shootout Winner

2021 getting back into bracket racing with a Gen3 Hemi powered 87 Cutlass.
 
Posts: 3103 | Location: Yes | Registered: July 08, 2009Reply With QuoteReport This Post
DRR S/Pro
Picture of "The Bender"
posted Hide Post
You can drop a plumb bob from the front of the crankshaft and the rear of the tail shaft and then from the pinion and then do chalk lines see if the drive shaft alignment is at least straight from one end to the other.

I recently did just that and found that my transmission tail shaft was one quarter inch out of alignment left to right.


272" Spitzer
540 Chevy
The Blower Shop XR1
FTI XPM Series Converter
FTI Level 6 Powerglide
3.69@199
.916 60'

2017 Bradenton Heads Up Madness
Open Outlaw Champ

2018 PDRA T/D #5
2019 PDRA T/D #2

2020 Retired From T/D Competition....

2020 Bradenton NMCA Hemi Shootout Winner

2021 getting back into bracket racing with a Gen3 Hemi powered 87 Cutlass.
 
Posts: 3103 | Location: Yes | Registered: July 08, 2009Reply With QuoteReport This Post
DRR Sportsman
Picture of Ron Gusack
posted Hide Post
quote:
Originally posted by "The Bender":
You can drop a plumb bob from the front of the crankshaft and the rear of the tail shaft and then from the pinion and then do chalk lines see if the drive shaft alignment is at least straight from one end to the other.

I recently did just that and found that my transmission tail shaft was one quarter inch out of alignment left to right.

I thought about a chalk line but I didn't think about doing it from the crank so it didn't make sense, but now I see. Hopefully I can trust the ATI degreed balancer to make dropping an accurate plumb line there. Thanks for the suggestion.
 
Posts: 465 | Location: Maryland | Registered: January 23, 2007Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
quote:
Originally posted by "The Bender":
You can drop a plumb bob from the front of the crankshaft and the rear of the tail shaft and then from the pinion and then do chalk lines see if the drive shaft alignment is at least straight from one end to the other.


I did exactly this but used my Dewalt rotary laser.

https://www.dewalt.com/product...ary-laser?tid=579196

If you know someone in the building trades, you might be able to borrow one.
 
Posts: 108 | Location: upstate NY | Registered: January 15, 2018Reply With QuoteReport This Post
DRR Sportsman
Picture of BD104X
posted Hide Post
quote:
Originally posted by "The Bender":
You can drop a plumb bob from the front of the crankshaft and the rear of the tail shaft and then from the pinion and then do chalk lines see if the drive shaft alignment is at least straight from one end to the other.

I recently did just that and found that my transmission tail shaft was one quarter inch out of alignment left to right.


^^ This. I just put a 5 speed in an old Corvette and had to fabricate a crossmember. I hung a string (plumb bob) from the balancer bolt & another from the pinion nut in the differential. Then ran a string from front to back - that gave me a location for the output shaft of the trans.


Billy Duhs - BD104X@gmail.com
 
Posts: 657 | Location: New Jersey | Registered: February 26, 2000Reply With QuoteReport This Post
DRR Sportsman
Picture of Ron Gusack
posted Hide Post
quote:
Originally posted by "The Bender":
You can drop a plumb bob from the front of the crankshaft and the rear of the tail shaft and then from the pinion and then do chalk lines see if the drive shaft alignment is at least straight from one end to the other.

I recently did just that and found that my transmission tail shaft was one quarter inch out of alignment left to right.

I can't drop a plumb bob from the crank because there's a cross member in the way. I used my DIY laser tool and I'm about an 1/8th out. Is an 1/8th off enough to require an adjustment? It's been this way for years and never seemed to cause a problem. Did you notice a difference when you eliminated that 1/4"?
 
Posts: 465 | Location: Maryland | Registered: January 23, 2007Reply With QuoteReport This Post



DRR S/Pro
Picture of "The Bender"
posted Hide Post
quote:
Originally posted by Ron Gusack:
quote:
Originally posted by "The Bender":
You can drop a plumb bob from the front of the crankshaft and the rear of the tail shaft and then from the pinion and then do chalk lines see if the drive shaft alignment is at least straight from one end to the other.

I recently did just that and found that my transmission tail shaft was one quarter inch out of alignment left to right.

I can't drop a plumb bob from the crank because there's a cross member in the way. I used my DIY laser tool and I'm about an 1/8th out. Is an 1/8th off enough to require an adjustment? It's been this way for years and never seemed to cause a problem. Did you notice a difference when you eliminated that 1/4"?



Haven't run the car after fixing the misalignment. I'll let you know after this weekend.


272" Spitzer
540 Chevy
The Blower Shop XR1
FTI XPM Series Converter
FTI Level 6 Powerglide
3.69@199
.916 60'

2017 Bradenton Heads Up Madness
Open Outlaw Champ

2018 PDRA T/D #5
2019 PDRA T/D #2

2020 Retired From T/D Competition....

2020 Bradenton NMCA Hemi Shootout Winner

2021 getting back into bracket racing with a Gen3 Hemi powered 87 Cutlass.
 
Posts: 3103 | Location: Yes | Registered: July 08, 2009Reply With QuoteReport This Post
DRR Pro
posted Hide Post
quote:
Originally posted by "The Bender":
You can drop a plumb bob from the front of the crankshaft and the rear of the tail shaft and then from the pinion and then do chalk lines see if the drive shaft alignment is at least straight from one end to the other.

I recently did just that and found that my transmission tail shaft was one quarter inch out of alignment left to right.


Were there any issues prior (vibration?) with it running 1/4” out of horizontal alignment??
 
Posts: 2678 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post
  Powered by Social Strata  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Lateral trans to rear alignment

© DragRaceResults.com 2024