 |
 |
 |
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
Bracket Talk Bracket Talk Forum Tech Talk - by Abruzzi Suggestions for hood and scoop for Lamplighter projectGo | New | Find | Notify | Tools | Reply | |
| Suggestions for hood and scoop for Lamplighter project | Login/Join |
| DRR Pro |
Fellow racers and builders, As a reminder, the Lamplight is a 3rd Camaro, specifically a 1982 model, but 82 - 92 takes the same hood. My struggle is with the hood and scoop. It will require about a 3" raised section to allow proper carb. Clearance. Other than that, the page is clean. Y'all help me out with some photos and suggestions. Thanks Larry Woodfin | ||
|
| DRR Elite |
no scoop, cowl hood | |||
|
| DRR Pro |
Ed, I did a Firebird a few years ago, and with that build, I installed a Harwood 3" cowl bolt-on [attaches to factory hinges and works like factory hood.] [Harwood is 8 miles from my shop] Looking back at those photos, I still like the look and that car was dead-on constant. Just brainstorming for other options before I buy something. Larry Woodfin | |||
|
DRR Sportsman |
I agree, cowl induction hood. I have a 2” on my 92, got it cheap, but I like the 3 or 4” better and would allow more clearance. The Pull-Out....for when you want to work smarter, not harder!!! | |||
|
| DRR Pro |
This is my Firebird from a few years ago with Harwood 3" hood Larry Woodfin Inbox_(278)_-_woodfinlarry_gmail.com_-_Gmail.html.zip (279 Kb, 134 downloads) | |||
|
| DRR Sportsman |
Big cowl. I love mine compared to the cars I drove with big scoops. I like the 6" look and it gives you room. I'm worried about carb spacer I want to install this year fitting but i run an air cleaner. I only have a 4". BG | |||
|
| DRR Pro |
My 3rd gen has a 4” Harwood cowl lift off hood. Same 2892 intake (they’re tall) as yours Larry, with a 3/4" primer spacer, 4.625 tall toilet and Uni FRS 950 low profile filter with 5/8” cut off mounting collar to clear top of hood cowl. Fits and works perfect. Ran it without and with filter…… exact same ET. You, not using an air filter, would probably be able to put a 2” or less cowl on it. Think about the next owner……. imho put a 4” cowl on it.  | |||
|
| DRR Trophy |
1320racer and markemark in my opinion have the set up. Larry on my 82 Camaro 4" harwood cowl,good vision and just right height.Was hopping to use same idea on my Corvette but wound up haveing to use a scoop. | |||
|
| DRR Elite |
I don't run an air filter/cleaner on my race cars and if you need more clearance, cut the manifold down which I guarantee has too much plenum volume, made worse with a spacer. | |||
|
| DRR Pro |
Mark, I looked at the Harwood liftoff style because it was more open underneath and a few pounds lighter. Larry Woodfin | |||
|
| DRR Elite |
Larry, what is this proper clearance you want to have? Fyi, here's mine...  That's the front bowl vent, the rear bowl vent is under the cowl. With 154MPH speed in the 1/4 mile at 3211 lbs. and with a 4150 carb, it's clearly not hurting performance. | |||
|
| DRR Pro |
Ed, I did not explain correctly. A 3" cowl hood will give adequate clearance, about like what is showing in your photo. Since Harwood is a short drive, and I am set up to buy from them. It is the best thing to do. Besides, I save $100.00 + shipping Larry Woodfin | |||
|
| DRR Pro |
Mark, In hindsight, would you do liftoff or factory hinges? Larry Woodfin | |||
|
| DRR Elite |
Hinges for the win!  I open my hood after every round to aid in cooling down and to visually inspect the engine bay. No help needed and no concern that the hood and/or fenders will get chipped/banged up during the R&R or that it will blow off the car or get stepped on, all of which I have seen. | |||
|
| DRR Pro |
Ed, I agree with your comments. Larry Woodfin | |||
|
| DRR Elite |
 | |||
|
| DRR Pro |
I purchased my car “as is” and the 4” Harwood cowl lift off hood was on it. I remove hood after every run to fuel the front 3 gal cell and have a visual of everything. If building new, I definitely would do hinges to make things much easier. | |||
|
| DRR Sportsman |
BG | |||
|
| DRR Pro |
That Uni FRS-950 (4150) is a foam filter. I use the Black color FRS-971 dirt filter element in it. The Red color FRS-970 element is much thinner. Soak with 50/50 solution of Simple Green to clean and let air dry. Re-oil with Uni Foam Filter Oil Spray. When using, if your engine backfires up into the air filter, it’ll melt the foam and suck the residue into the engine. My engine does not backfire. Even when starting full cold in 30* temps never a problem. If you do have backfiring issues cold starting when using this filter, it’s best to remove prior to first start. | |||
|
| DRR Elite |
I have seen many cars over the years backfire and the filter catch fire. Not good and it's one of the reasons I don't run an air filter. | |||
|
| Powered by Social Strata | Page 1 2 |
 | Please Wait. Your request is being processed... |
|
Bracket Talk Bracket Talk Forum Tech Talk - by Abruzzi Suggestions for hood and scoop for Lamplighter project
 |
 |
 |
 |
