Go
New
Find
Notify
Tools
Reply
  
Milky oil??
 Login/Join
 
DRR S/Pro
Picture of Eman
posted
Didn't want to hijack another person's thread.
In that discussion people say that one oil milks worse than others. Is there any truth to that? Is the milking the water being whipped up into the oil or is it excess alcohol? Are there oils that resist having that happen? Chemically what is actually happening that causes milking?
 
Posts: 1560 | Location: E TN | Registered: February 13, 2009Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
like a few said in the other posts....keep the idle mixture right, be sure to warm engine at the end of the day, vacuum pump helps a ton with moisture.
 
Posts: 560 | Location: somewhere between been and never was | Registered: November 03, 2002Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
Keep the intake warm and you'll have no condensation dripping off the bottom side of it, milking the oil.
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Top Comp
Picture of Curly1
posted Hide Post
I have a friend who did a home test with oil and water. He took two different brands of oil and put them in jars with same amount of oil and same amount of water and shook them up. He said one brand separated the water from the oil in 30 minutes to a few hours. They other has still not separated and is milky after a few months. One brand was Valvoline VR1 Racing oil. I do not know what the other brand was or which one separated and which one did not.
So YES, some oils milk worse than others. still root cause of it is water and alcohol in the oil. To me it does not matter if the oil separates quickly or mixes in milking the oil it is not good for it.

As for the water? Well it is in the air the motor takes in. Alcohol runs cooler so it tends to have more of a milking problem than gas.
Water boils and evaporates out at 212* and alcohol about 160* and both at lower temps under vacuum.

The key is to get it good and warm at end of each race day, I get water temp up over 210* or so and then you see vapor coming out of the vacuum pump tank.

I HATE DRAGSTERS is right about the Idle mixture that is huge on how much alcohol you waste and how much moisture gets in the oil. If you can lean it does you warm up quicker use way less fuel and does not milk oil as bad.


https://postimg.cc/gallery/np3zpruo/
"Dunning-Kruger Effect"
-a type of Cognitive bias where people with little expertise or ability assume they have superior expertise or ability. This overestimation occurs as a result of the fact that they do not have enough knowledge to know they don't have enough knowledge.

Before you argue with someone ask yourself, "Is this person mentally mature enough to grasp the concept of a different perspective?" If not there is no point to argue.

4X NE2 CHAMPION. 2020 TDRA NE2 Champion
 
Posts: 4235 | Location: United States of Texas | Registered: April 02, 2011Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
As for oils fixing an issue, this is not want you should be concerned with! Fix the problem, there is no reason an alky feed motor should milk the oil, period! You don't want water or water vapor in the crankcase whether it's mixed with or separated from the oil, ever.

Usually it's idling to rich that causes the issue. When idling the engine should gain temp slowly without the fan running, this will get you close. The use of a vac pump will do wonders getting the moisture out along with never put the car away cold. The other thing that can help a bunch, especially for those using alky to double enter and cool the car while running, is use a primer plus gas system which will allow you to get the motor, and more importantly the engine oil hot before you park it in the trailer after racing.
 
Posts: 2163 | Location: Tewksbury, MA,USA | Registered: November 03, 2000Reply With QuoteReport This Post
DRR S/Pro
Picture of Lenny5160
posted Hide Post
I’d much prefer that my oil and fuel/water remain mixed. Compromised oil is not ideal, but it’s much better than your crank/rods spinning on a thin layer of straight fuel or water.


Tony Leonard
 
Posts: 3219 | Location: Inver Grove Heights, MN | Registered: March 18, 2004Reply With QuoteReport This Post
DRR Top Comp
Picture of wideopen231
posted Hide Post
milk is simply moisture in i oil that should not be there. It can be from too much blow bye on rings letting alky into oil. Too rich system forcing unburned fuel into oil. It cn be from water from leak that gets into oil.

99% of time if running alky its i from over rich. Be it idle or just fat in general.




America home of free. Brought to you by 2nd amendment.
 
Posts: 4462 | Location: Greensboro NC | Registered: May 24, 2011Reply With QuoteReport This Post



DRR S/Pro
Picture of Eman
posted Hide Post
OK, so the milking is both alcohol and water in the oil. And some oils will keep it in suspension longer than others.
 
Posts: 1560 | Location: E TN | Registered: February 13, 2009Reply With QuoteReport This Post
DRR Sportsman
Picture of BD104X
posted Hide Post
quote:
Originally posted by Eman:
OK, so the milking is both alcohol and water in the oil. And some oils will keep it in suspension longer than others.

Yes.... Not enough temperature will do it and too rich will do it. If an alcohol combo is excessively rich, it's slow to build temperature so it really compounds the issue. As others have said, if your tuneup is right and you keep your temps up, its pretty much a non issue. I stage at 155-160, don't use the fan unless I'm hot-lapping it and my car is pretty deadly - I change my oil about every 75 runs.


Billy Duhs - BD104X@gmail.com
 
Posts: 648 | Location: New Jersey | Registered: February 26, 2000Reply With QuoteReport This Post
  Powered by Social Strata  
 


© DragRaceResults.com 2024