DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Procharger equivalent to baby blower
Go
New
Find
Notify
Tools
Reply
  
Procharger equivalent to baby blower
 Login/Join
 
DRR Trophy
posted
Has anyone tried running a smaller/low boost procharger on a bracket car, something equivalent to a 250 blower?
 
Posts: 66 | Location: Glen Burnie | Registered: May 30, 2011Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
quote:
Originally posted by top189h:
Has anyone tried running a smaller/low boost procharger on a bracket car, something equivalent to a 250 blower?


Sure, belt driven. A friend bought a sbc kit, everything minus Blow thru carb, for around $3,500 I think.

He still hasn't out run my sbc n/a, his goal. I think he's been 6.08 @ 3200 lbs, 406 sbc on gasoline. Gasoline, really isn't the hot ticket ProCharger.
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
I don’t think it would work very well, at least not trying to do the same thing everybody else is doing where they take a 1000 hp engine and bolt on a couple hundred hp.

I looked into putting a small turbo on a Bbc to make a few psi of boost. It’s not really possible and the exhaust side wasn’t the problem.

A small compressor wheel on a big engine at low boost ends up way off the map.

A roots blower doesn’t really care what’s underneath. The less restriction a centrifugal compressor has, the more power it takes to turn.

For a procharger or a turbo to end up in that same ~1200-1300 hp range economically, I think you have to start off with a much smaller cubic inch long block.
 
Posts: 936 | Location: my own little world | Registered: July 20, 2005Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
Centrifugals are a little more efficient than roots all things considered.

I think we can all agree that a roots (or a variant of it) makes boost as soon as you open the throttle.

Centrifugals need RPM to make boost, and that fact alone can work for or against you. It has everything to do with the pulley ratio, gear ratio (in the blower itself) and the compressor wheel design. I've driven some street procharged cars that make boost off of idle but at are max blower speed by 5500 RPM, and I've driven others that were a little on the sluggish side down lower, but the more RPM you wring out of them the more power it makes-THOSE, are fun.

Turbo's, just real hard to get anything with a budget in mind, that will work correctly. Either too small or too big. There is a VGT (or VNT depending on the manufacturer, same principle for both), and that can certainly make up for a lot, however it hasn't gained a lot of steam with gas burners. Diesels yes but not too much with gas burners. Could be due to the higher EGT. Dunno. We tried one on a 2.3 Ford once, 28 psi at 1600 RPM and held it to the 6250 fuel cut, but it took a LOT of tuning, ingenuity, rigging, and frankly wasn't worth the aggravation. On that deal it would bend the stock rods.

speaking of turbo's I'd like to someday do a footbrake car with a turbo (or two), just don't know how to go about it-and still maintain consistency.
 
Posts: 118 | Location: Il,IL | Registered: March 22, 2021Reply With QuoteReport This Post
  Powered by Social Strata  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Procharger equivalent to baby blower

© DragRaceResults.com 2024