DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Moroso accumulator fitting removal
Go
New
Find
Notify
Tools
Reply
  
Moroso accumulator fitting removal
 Login/Join
 
DRR Elite
posted
Not sure how to tackle this one. I have an accumulator with a solenoid on it, that I need to remove from the accumulator. But of course the end of the unit turns when I try to spin it out. There are two spanner holes, but I don't have a spanner wrench that would help here. Not even completely sure where to buy one.

Any tricks to holding that end to get the fittings out without special tools? Or guidance where and what to get to hold this?


Foxtrot Juliet Bravo
 
Posts: 6453 | Location: Illinois | Registered: July 08, 2004Reply With QuoteReport This Post
DRR S/Pro
Picture of SCDIV1
posted Hide Post
Use 2 punches in the spanner holes.
Bridge the punches with a bar or big screwdriver to hold the plate.

If that does not work you could make a spanner wrench from some flat stock and a couple bolts.
I just made one to do my 9" ford rear.

I do remember wrestling with my accusump to remove the fitting.....just don't recall exactly what I did.....
 
Posts: 2735 | Location: Where ever I am, I'm here and it's me | Registered: March 15, 2007Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
What Rich said. I made one out of some flat bar stock and couple of bolts. Worked like a champ. You can cut out part of the bar stock to clear the solenoid or build it in a Y shape. Good luck!


Clowns to the left of me, Jokers to the right. Here I am.......
 
Posts: 5334 | Location: stuck in the middle with you! | Registered: March 11, 2002Reply With QuoteReport This Post
DRR S/Pro
Picture of CURTIS REED
posted Hide Post
You should be able to pick up an adjustable spanner wrench pretty easy.

You could just pull the end cap out and clamp it flat to a table top also.

Curtis



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 3149 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
DRR Elite
posted Hide Post
I tried the two punches first, but of course the fitting was completely in the way of that setup. I need to either do the flat bar or buy a spanner. Thank you guys!


Foxtrot Juliet Bravo
 
Posts: 6453 | Location: Illinois | Registered: July 08, 2004Reply With QuoteReport This Post
DRR S/Pro
Picture of Eman
posted Hide Post
I'm late to the party and when I read the post I knew that fitting would be in your way so you couldn't use the 2 punches or the flat stock. What you can use is 2 pieces of flat stock. Put a bolt in the ends of the flat stock and then bolt the other ends of the flat stock together making your own pin spanner.
 
Posts: 1572 | Location: E TN | Registered: February 13, 2009Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
Remove the snap ring, the take the entire end plate to a vise and remove the fittings. Don’t forget to remove the pressure first!
 
Posts: 37 | Location: Pittsburgh, pa | Registered: October 10, 2017Reply With QuoteReport This Post



DRR Elite
posted Hide Post
ordered a cheap spanner from Amazon. Good point about the pressure! Im not entirely sure the valve was opening. So I will crack it and see if I get a stream. Guess I can pull the air pressure out of the other end if there is oil in it. But I can keep the end on it this way. Easy. Thanks all!


Foxtrot Juliet Bravo
 
Posts: 6453 | Location: Illinois | Registered: July 08, 2004Reply With QuoteReport This Post
DRR S/Pro
Picture of SCDIV1
posted Hide Post
The solinoids are directional and only go one way to work right.

Twice I've managed to splatter myself and the side of my trailer with oil at the track from Accusump.

The side marked IN on the solenoid go's toward the engine IIRC.....I'm at work so I can't confirm that but am pretty sure.

If you put it in backwards it won't hold pressure.....

My car has not run for about 6 months and still has 60lbs in the tank.....


I honestly don't recall how I got mine apart but know for sure I took it off the car and pulled the end apart at least once.

It was not working right and was erratic....

The piston was likely being hung up at times from the case being slightly squeezed by the mounting clamps I used to mount it. Bought them from Chassis Shop-Pro Works...

Holds tank on flat mount from Racetech above trans. saddle clamped to upper frame rails...

I moved the clamps to the ends and no more issues....

Its ugly but I could care less.....it works...
 
Posts: 2735 | Location: Where ever I am, I'm here and it's me | Registered: March 15, 2007Reply With QuoteReport This Post
DRR S/Pro
Picture of CURTIS REED
posted Hide Post
I pull mine apart every time the engine comes out and clean it as regular maintenance.



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 3149 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
We made a spanner out of a piece of round stock and a couple bolts.


"I am not ashamed to confess I am ignorant of what I do not know."
Marcus Tullius Cicero
 
Posts: 1028 | Location: Las Vegas, NV | Registered: April 14, 2004Reply With QuoteReport This Post
DRR Elite
Picture of adv ET 266
posted Hide Post
I found it to be best to take the clip out and remove the cover. Way more manageable and I’ve done both ways. The bonus is you can clean out the inside that will have oil sedament.
I removed the gauge and put a compact fiting on so I could tuck mine between the belt driven fuel pump and system 1 filter on my BBC. One less clunky thing to see.



2005 2000lb 4 link dragster
home brew 582 BBC Dart 355
1.058
2.98
4.629@149
6.094
7.310@185

 
Posts: 12175 | Location: 33463 | Registered: February 04, 2004Reply With QuoteReport This Post
  Powered by Social Strata  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Moroso accumulator fitting removal

© DragRaceResults.com 2024