Go
New
Find
Notify
Tools
Reply
  
Mill accessory?
 Login/Join
 
DRR Sportsman
posted
I have a small benchtop mill (jet15) that I’m just starting to get comfortable with. I’m using it to make a few brackets for my new project out of 3/8 aluminum. Some of these are irregularly shaped. It would be nice to “free hand” some sections. Is there anything I could use to keep a 3/8 plate level to the table but let me safely guide it? For instance, I needed a plate to butt tightly against a timing cover. Easy enough to transfer the shape I needed but difficult to cut that shape with manual xy control. Don’t need much precision just the ability to cut odd curves while keeping control of the plate.
 
Posts: 928 | Location: my own little world | Registered: July 20, 2005Reply With QuoteReport This Post
DRR Top Comp
Picture of wideopen231
posted Hide Post
normally a rotatory table is used.For odd curve you have to offset the material . Might be formula but I have always used try and try again till it works method.LMAO

Check on ebay sometimes there few old ones for sale.

Mills are cheap and accessories can cost lot more than base mill.




America home of free. Brought to you by 2nd amendment.
 
Posts: 4171 | Location: Greensboro NC | Registered: May 24, 2011Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
I've bought lots of Bridgeport parts and tooling from these guys, easy to work with and very knowledgeable, give them a look.

https://www.machinerypartsdepot.com/
 
Posts: 138 | Location: Midlothian, Texas | Registered: October 19, 2000Reply With QuoteReport This Post
DRR Pro
Picture of Roger McGinnis
posted Hide Post
Let's start with,,,,,,,,,, you don't buy a mill to freehand parts.



ΜΟΛΩΝ ΛΑΒΕ
 
Posts: 559 | Location: Republic of Texas | Registered: January 16, 2011Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
quote:
Originally posted by Roger McGinnis:
Let's start with,,,,,,,,,, you don't buy a mill to freehand parts.



Nonsense


.
Dave



F J B

 
Posts: 4447 | Location: Earth | Registered: February 08, 2006Reply With QuoteReport This Post
DRR Trophy
Picture of 433red
posted Hide Post
quote:
Originally posted by Roger McGinnis:
Let's start with,,,,,,,,,, you don't buy a mill to freehand parts.



Nonsense


Agree 100% with Dave. My mill and lathe are used for 1 off items and repairs. Rarely are duplicate items made on my equipment.

Responding to the original post, a rotary table is a great tool to have. Elevating and safely securing the materials onto the table to follow scribed layout images free hand would be considered S.O.P. in my shop...
 
Posts: 102 | Location: Ga | Registered: July 28, 2007Reply With QuoteReport This Post
DRR Elite
posted Hide Post
I'm gonna need a rotary table next it looks like.


Foxtrot Juliet Bravo
 
Posts: 6367 | Location: Illinois | Registered: July 08, 2004Reply With QuoteReport This Post



DRR Pro
Picture of Roger McGinnis
posted Hide Post
quote:
Originally posted by 433red:
quote:
Originally posted by Roger McGinnis:
Let's start with,,,,,,,,,, you don't buy a mill to freehand parts.



Nonsense


Agree 100% with Dave. My mill and lathe are used for 1 off items and repairs. Rarely are duplicate items made on my equipment.

Responding to the original post, a rotary table is a great tool to have. Elevating and safely securing the materials onto the table to follow scribed layout images free hand would be considered S.O.P. in my shop...


I would consider "free hand", something not done in a mill vise or clamped to a stationary or rotary table.



ΜΟΛΩΝ ΛΑΒΕ
 
Posts: 559 | Location: Republic of Texas | Registered: January 16, 2011Reply With QuoteReport This Post
DRR Sportsman
Picture of Dave Koehler
posted Hide Post
Rough it in the best you can.
Finish sand to shape.


Dave Koehler - Koehler Injection - http://www.koehlerinjection.com
Fuel Injection - Nitrous Charger - Nitrous Master Software - Balancing
99% of fuel injection problems are electric.
 
Posts: 351 | Location: Urbana, IL 61802 | Registered: December 03, 2003Reply With QuoteReport This Post
DRR Sportsman
Picture of Dave Koehler
posted Hide Post
Did someone mention a rotary table.
I have one up on craigslist.
https://chambana.craigslist.or...able/7128545006.html


Dave Koehler - Koehler Injection - http://www.koehlerinjection.com
Fuel Injection - Nitrous Charger - Nitrous Master Software - Balancing
99% of fuel injection problems are electric.
 
Posts: 351 | Location: Urbana, IL 61802 | Registered: December 03, 2003Reply With QuoteReport This Post
DRR Pro
Picture of CURTIS REED
posted Hide Post
Heck you can do what you are talking about in a drill press and or a mill. Take a double cut 1/4" die grinder burr and bring the quill down so the end of the burr is below table top height. Have your part roughed in close to shape. Use LPS-2 for lube (WD-40 if nothing else) and bring your part to final shape at about 1000rpm. Don't get real aggressive and it will work fine. If you use something with too much helix it will try to lift your part that's why I say a double cut burr, which you usually wouldn't use on aluminum. Sand it to a nice finish.

Now is this the best way to do it? No, but it will work easy peasy.



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 2916 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
Good tip on the double cut burr. I never tried that on my drill press cuz I tried it on someone else’s one time and the chuck fell out.

Just for fun i tried sliding 3/8 aluminum along the top table into a 2 flute 1/2” cutter at 1600 rpm. That doesn’t work very well.
 
Posts: 928 | Location: my own little world | Registered: July 20, 2005Reply With QuoteReport This Post
DRR Sportsman
Picture of Dave Koehler
posted Hide Post
Dang, that is scary. Who held your beer?


Dave Koehler - Koehler Injection - http://www.koehlerinjection.com
Fuel Injection - Nitrous Charger - Nitrous Master Software - Balancing
99% of fuel injection problems are electric.
 
Posts: 351 | Location: Urbana, IL 61802 | Registered: December 03, 2003Reply With QuoteReport This Post
  Powered by Social Strata  
 


© DragRaceResults.com 2024