Page 1 2 3 4 ... 11
Go
New
Find
Notify
Tools
Reply
  
Tips !
 Login/Join
 
DRR S/Pro
Picture of Rick Bailey
posted
Back in the BC ages (before Computers) I used to read "Car Craft", "Hot Rodding" and they would from time to time run a Tips section or stories that guys would send in to share. This might be cool to do here.

One that I can think of is for the dragster guys, when filling water in the engine. There always seems to be that air pocket that kicks ones butt. heres what I found to work well and easier than a pressure tester. Pick up one of those long smooth tapered funnels (18" inches or so) Wal-mart has them. Push the funnel into the water neck the tapered funnel will seal very well to the neck. now you will have a water level 12" or more above the highest point within the engine or radiator. keep the funnel full of water while you use the bleeder on the radiator to bleed out all the air.

It works !

Your Turn

Ric

This message has been edited. Last edited by: Rick Bailey,
 
Posts: 223 | Location: Illinois | Registered: April 02, 2007Reply With QuoteReport This Post
DRR S/Pro
Picture of David Covey
posted Hide Post
1. Grease on a tap will keep shavings from falling into whatever you are tapping..

1a. Use a vacuum cleaner to clean out lifter valley and inside ports after cleaning intake gaskets.

Dave


"It is usually futile to try to talk facts and analysis to people who are enjoying a sense of moral superiority in their ignorance." -Thomas Sowell
 
Posts: 3304 | Location: American By Birth Texan By The Grace Of God  | Registered: April 29, 2004Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
If you need to cap off your tube of silicone after opening it try an electricians wire nut.


No matter how many times you paint over a shadow it's still there.


 
Posts: 684 | Location: Galesburg Il. | Registered: December 10, 2006Reply With QuoteReport This Post
DRR Top Comp
Picture of Guy M. Price
posted Hide Post
Put a smoke alarm in your enclosed trailer with a siren or light outside your trailer that the smoke alarm will trigger so you aren't pulling a blow torch down the highway without knowing it! And don't lock your doors when towing! You may need to get in their quickly and as far as I know there aren't to many thieves that steal stuff "on the run"! Also put a name or number on top of your trailer so it can be spotted from the air should it be stolen. Don't know too many thieves that go up and check the top of the trailer for anything! Eek Razz Wink Cool


"The Price is Right, but seldom official. If you find yourself in a hole, for God's sake, quit digging! I'm not old, I'm chronologically gifted!"
 
Posts: 6498 | Location: At Los Dos Molinos! | Registered: October 25, 2000Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
On your scoop plug drill a couple of 1" holes just through the plastic in front but not through the foam. If you accidentally rev the engine with the plug in place it could prevent sucking the top of the scoop in.


No matter how many times you paint over a shadow it's still there.


 
Posts: 684 | Location: Galesburg Il. | Registered: December 10, 2006Reply With QuoteReport This Post
DRR Top Comp
Picture of ChuckT
posted Hide Post
This is more of a reminder...

Always, always, ALWAYS degree in your cam. I didn't, and was wrong when I thought I put it back in straight up. Hung all 8 exhaust valves open just enough to get dinged by the pistons. You can see the mark on the piston at about 2 o'clock.



'81 Cutlass, KX05, Keystone Raceway Park
Millerstown Pic-A-Part, Tarentum, PA
Wholesale Transmission, New Kensington, PA
Thinking of Nikki and Mark - forever 53
 
Posts: 7228 | Location: Pittsburgh | Registered: December 07, 2005Reply With QuoteReport This Post
DRR Pro
posted Hide Post
the containers that the "white creamy" hand cleaner comes in makes a good carb cover for a 4150.


Tee
wjoh155052@aol.com

Schooled by Scotty
http://www.scottyrichardsonsdragracingschool.com/
615-804-2487

My Home Track
New London Dragway.

www.biondoracing.com
www.racepartdepot.com

Loose Change does not smoke tires because i didn't teach him to do that.
 
Posts: 2159 | Location: Rustburg VA | Registered: July 16, 2005Reply With QuoteReport This Post



DRR Sportsman
posted Hide Post
quote:
Originally posted by Ragidy57:
the containers that the "white creamy" hand cleaner comes in makes a good carb cover for a 4150.


Thanks Tee!


Mack Johnson

pump gas 347
6.435@104



 
Posts: 885 | Location: Waiting to see who Raylan kills next. | Registered: December 30, 2000Reply With QuoteReport This Post
DRR Pro
Picture of chasracer
posted Hide Post
If you do any kind of bodywork or painting, sandpaper is a standard commodity.

#1 Use a file folder to keep your sandpaper in, this will help keep the edges from curling up. You can even use multiple folders to organize the various grits.

#2 Mount a regular hacksaw blade to the front of your workbench with wood screws. Leave it slightly loose and it makes a dandy sandpaper cutter. I have used the same blade for over 20 years now.
 
Posts: 1135 | Location: The problem is not the problem. The problem is your attitude about the problem. Savvy?” ~~ Captain Jack Sparrow ~~ | Registered: August 21, 2000Reply With QuoteReport This Post
DRR Pro
posted Hide Post
Send me $20 and I promise I will red light the next time we run. Wink Big Grin

Or how about don't play leaf frog with a unicorn. Smile


Jeremy McKague
s/c 341a
 
Posts: 589 | Location: .001 in front of you | Registered: October 18, 2000Reply With QuoteReport This Post
DRR Pro
Picture of CURTIS REED
posted Hide Post
If you need to drill a hole in sheet metal use a step drill, it will make a perfectly round hole unlike a drill. Available at electrical supply stores or tool supplies.

Curtis



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 2916 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
DRR S/Pro
Picture of banjo
posted Hide Post
For doors cars where it is a pain to get at the tranny lines, Cut the lines were they are easily accessible and install bulk head fittings. You can then unhook the lines at that point instead of at the tranny. Makes it alot easier when you are pulling the trans.


Bill Simpkins
74 Nova
SBC 406
3240 pounds
Speierracing heads

60 1.27 (10/16)
1/8 6.03@111 (10/16)
Best 9.87@131 on the rev limitor 1 Feb 2013


nova

quarterpanelview

wheelie

FTI Converter
www.speierracingheads.com

 
Posts: 1829 | Location: San Angelo | Registered: March 07, 2005Reply With QuoteReport This Post
DRR S/Pro
Picture of Rick Bailey
posted Hide Post
Batterys

Always keep the battery in your race car and your daily drivers or anything "Clean"

Try this, if you've got a vehicle with a dirty greasy case or the same around the termials. take a volt meter and with the black probe to ground (or even to the grn side of the battery) and take the red probe and probe around on the case ...... you'll see direct voltage that is draining to ground. I've seen as much as 5 to 10 volts......

This is something that a truck, motorhome or something that sits alot with out much visual maintance will be prone to. And will not crank after sitting for some time.
This something that is more prone to acid batterys
Just clean the battery and starting problem gone.

Ric
 
Posts: 223 | Location: Illinois | Registered: April 02, 2007Reply With QuoteReport This Post
<wildcargo>
posted
Pam cooking spray on valve cover gaskets thay won't stick and tare
 
Reply With QuoteReport This Post



DRR Elite
Picture of adv ET 266
posted Hide Post
Always jack up you car rear when at rest in trailer for more than a week. Keeps the slicks nice a round Wink

Let you parachute out with bridle shut spring relaxed when not using for extended time.



2005 2000lb 4 link dragster
home brew 582 BBC Dart 355
1.058
2.98
4.629@149
6.094
7.310@185

 
Posts: 12149 | Location: 33463 | Registered: February 04, 2004Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
store funnels in a plastic bag to keep them clean when in storage.
 
Posts: 690 | Location: Bucks Co Pa | Registered: January 23, 2003Reply With QuoteReport This Post
DRR Trophy
Picture of Dave Stuckey
posted Hide Post
make TIPS a sticky
 
Posts: 57 | Location: French Creek WV | Registered: August 02, 2007Reply With QuoteReport This Post
DRR S/Pro
Picture of David Covey
posted Hide Post
Spray oven cleaner for degreasing..

Muretic acid makes aluminum intakes look like new..(don't leave on for extended time)

Fishing lure box for small parts, jets, MSD chips..

Wrap tape on drill bits as depth gauge..

Spring clips for holding brooms and lawn chairs to trailer wall..

Dave


"It is usually futile to try to talk facts and analysis to people who are enjoying a sense of moral superiority in their ignorance." -Thomas Sowell
 
Posts: 3304 | Location: American By Birth Texan By The Grace Of God  | Registered: April 29, 2004Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
Never use rol-loc discs to clean off gasket material unless the piece is off the engine and can be completely cleaned....those fibers will wreak havoc on bearings,enough of 'em can plug an oil pick-up....Jasper states warranty null and void if they find it one of their engines.

Those handheld scotch bright pads will,however,restore the "satiny" look to brushed look fabbed valve covers etc.

An import car air to air intercooler makes a nice,strong,lightweight aluminum radiator for cars that don't need alot of radiator..such as alky motors. I have used one for years,work great.
 
Posts: 214 | Location: lake ann,michigan | Registered: November 19, 2002Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
When packing your parachute use weed wacker string. it slides nice and won't saw on the loop when you pull it through.


No matter how many times you paint over a shadow it's still there.


 
Posts: 684 | Location: Galesburg Il. | Registered: December 10, 2006Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2 3 4 ... 11 
 


© DragRaceResults.com 2024