DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    BULLET CAMS - BRODIX sbc Track 1 heads
Page 1 2 3 4 ... 15
Go
New
Find
Notify
Tools
Reply
  
BULLET CAMS - BRODIX sbc Track 1 heads
 Login/Join
 
DRR Top Comp
posted
Are there any examples of AFR sbc 23 degree cylinder heads going faster 3200 lbs n/a?

This Brodix 23 degree, Bullet cams combo is the fastest MPH I've seen n/a 3200 lbs.

It's nothing more than a viral internet rumor, AFR 23 degree cylinder heads make more power than their counterparts Brodix, out of the box - Make believe.

Fact.



 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
You bring this up on every post, and now you started your own thread.

Dude, check into meth rehab.
 
Posts: 287 | Location: Midwest  | Registered: January 12, 2015Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
It's a provable performance topic, fundamental to drag racing using out of the box small block Chevrolet 23 degree cylinder heads.

There has been more 3000 lb plus 23 degree sbc combo's go down down drag strips, than any other combo. It's the most plentiful combo ever.

Fundamental drag racing topic, off the shelf, over the counter, out of the box 23 degree sbc cylinder heads.


 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Top Comp
Picture of Curly1
posted Hide Post
I can tell you mine is making way more power and it is AFR 235 (23 degree heads)with light hand touch up / port match, Enderle hat injection 1775 Lbs and runs 4.92 @139 MPM in Texas with 28* timing. Even in really bad air like 3500 DA I am still at 5.02. If I remember right ran a 5.09 at 7550 DA. I think a 6.41 @ 111 and you are probably close to sea level is not that impressive to me.
And mine is not set on kill I like to keep my stuff fairly conservative. Has a 4.10 rear gear, 1.80 low gear, 6400 stall and 32 inch tall tire.
I mean it is a good motor Crower cranks, Crower rods, Crower shaft rockers, Diamond pistons and I think I am around 14 to 1 on the compression. Like I say I like to keep it relatively conservative. I do run Bullet cams and I like them but I told them when I bought the cam I wanted fairly conservative and relatively easy on valve train.
My motor made 760 Hp on a honest dyno.
I bet you are not any where near there. At 1775 Lbs I am way lighter than you but I bet if you ran the numbers yours comes up short big time.


https://postimg.cc/gallery/np3zpruo/
"Dunning-Kruger Effect"
-a type of Cognitive bias where people with little expertise or ability assume they have superior expertise or ability. This overestimation occurs as a result of the fact that they do not have enough knowledge to know they don't have enough knowledge.

Before you argue with someone ask yourself, "Is this person mentally mature enough to grasp the concept of a different perspective?" If not there is no point to argue.

4X NE2 CHAMPION. 2020 TDRA NE2 Champion
 
Posts: 3966 | Location: United States of Texas | Registered: April 02, 2011Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
The debate isn't about what you run at x amount of weight vs 3200 lbs.

It's about no can outrun this speed on the planet 3000 lbs plus, with out of box AFR cylinder heads.

There's more 3000 lb plus cars going down drag strips than any other combo.

So there's a bunch of examples to choose from.

Brodix has the fastest sbc 23 degree out of the box cylinder head currently.

I'm not sure why the rumor persists that says AFR heads make more power out of the box than Brodix, when there's no/zero examples in existence.

This message has been edited. Last edited by: Mike Rietow,
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Pro
posted Hide Post
quote:
Originally posted by Curly1:
I can tell you mine is making way more power and it is AFR 235 (23 degree heads)with light hand touch up / port match, Enderle hat injection. I think I am around 14 to 1 on the compression. I do run Bullet cams and I like them but I told them when I bought the cam I wanted fairly conservative and relatively easy on valve train. My motor made 760 Hp on a honest dyno.


Nice! I like injection. What cu in and cam lift numbers??
 
Posts: 2434 | Location: 53056 | Registered: December 30, 2009Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
quote:
Originally posted by markemark:
quote:
Originally posted by Curly1:
I can tell you mine is making way more power and it is AFR 235 (23 degree heads)with light hand touch up / port match, Enderle hat injection. I think I am around 14 to 1 on the compression. I do run Bullet cams and I like them but I told them when I bought the cam I wanted fairly conservative and relatively easy on valve train. My motor made 760 Hp on a honest dyno.


Nice! I like injection. What cu in and cam lift numbers??


Long rod ratio so it'll have symmetrical lobes, shorter duration and tighter lobe separation.

Unless you're building a Super Pro bracket racing specific lightweight dragster with a long rod BBC , tall deck. Smile

It's a tall deck 454 sbc.
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post



DRR Top Comp
posted Hide Post
With evidence on any given topic, I'm more than willing to admit the possibility I'm wrong.


 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Elite
posted Hide Post
quote:
Originally posted by Mike Rietow:
Brodix has the fastest sbc 23 degree out of the box cylinder head currently.

I disagree, ALL PRO does.
 
Posts: 13522 | Location: NJ | Registered: August 20, 2000Reply With QuoteReport This Post
DRR Pro
Picture of CURTIS REED
posted Hide Post
quote:
Originally posted by 1320racer:
quote:
Originally posted by Mike Rietow:
Brodix has the fastest sbc 23 degree out of the box cylinder head currently.

I disagree, ALL PRO does.


Ed, you should have added the no one cares emoji



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 2910 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
DRR Sportsman
Picture of Bob Deniker
posted Hide Post
Was this a one time deal like your 5.90 run ? I'm not sure what mph should be on a mid 10 second car. It's been a long time since I was in that speed range.
 
Posts: 621 | Location: Latrobe Pa. | Registered: July 30, 2007Reply With QuoteReport This Post
DRR Top Comp
Picture of Curly1
posted Hide Post
This is dial in bracket racing you can put as slow of a number on there as you want. If you think it is fast put your number on it and run it.

If you are happy and impressed with that performance that is all that matters. It is your car and you build it to make you happy. Going to take a lot more than that to impress me though.


https://postimg.cc/gallery/np3zpruo/
"Dunning-Kruger Effect"
-a type of Cognitive bias where people with little expertise or ability assume they have superior expertise or ability. This overestimation occurs as a result of the fact that they do not have enough knowledge to know they don't have enough knowledge.

Before you argue with someone ask yourself, "Is this person mentally mature enough to grasp the concept of a different perspective?" If not there is no point to argue.

4X NE2 CHAMPION. 2020 TDRA NE2 Champion
 
Posts: 3966 | Location: United States of Texas | Registered: April 02, 2011Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
quote:
Originally posted by Bob Deniker:
Was this a one time deal like your 5.90 run ? I'm not sure what mph should be on a mid 10 second car. It's been a long time since I was in that speed range.


I've been faster with a BLP 4500 Dominator carb.

It's been forever since anyone else has been in this MPH range at 6.40. Forever like as in never, 23 sbc 3200 lbs.

 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
Everyone said it had nitrous on it when it dipped in the 5's off the trailer new combo I threw together engine, transmission, ring and pinion.

I about fell out of my chair laughing.

So much for that idea eh?

Brodix is fastest, where this idea comes from AFR makes more power beats me.

Must come from some snake oil salesman expert like Dr. Farci LoL.

Hate the Truth all you want, it won't change it.
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post



DRR Top Comp
posted Hide Post
It's like the BS story being sold $$ on the Bills player saying he suffered blunt force trauma.

You could hit the guy in the chest with a sledge hammer. With the sternum-chest plate on Douglas shoulder pads the NFL uses, he wouldn't have a scratch.

That dude had a pre-existing ....... induced condition, why he fell out.

So much BS is sold $$.
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Sportsman
Picture of TomR
posted Hide Post
quote:
Originally posted by Bob Deniker:
I'm not sure what mph should be on a mid 10 second car. It's been a long time since I was in that speed range.


My junk at Mason Dixon runs high 6.40's @ 104-105mph. This is with a 355ci, Brodix Track 1 heads and a PBM 555 lift roller cam. Nothing special or fast.

https://www.youtube.com/watch?v=Rlef_8dopsI

https://www.youtube.com/watch?v=Smcr5D3zeNE


72 Nova "Hooptie"
 
Posts: 734 | Location: Hanover, MD | Registered: June 20, 2016Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
quote:
Originally posted by Tom Reyer:
quote:
Originally posted by Bob Deniker:
I'm not sure what mph should be on a mid 10 second car. It's been a long time since I was in that speed range.


My junk at Mason Dixon runs high 6.40's @ 104-105mph. This is with a 355ci, Brodix Track 1 heads and a PBM 555 lift roller cam. Nothing special or fast.

https://www.youtube.com/watch?v=Rlef_8dopsI

https://www.youtube.com/watch?v=Smcr5D3zeNE


104-105 mph is par for the course, 6.40 3000 plus lbs 23 sbc.

My Nova the rear quarters were cut like yours when I got it. You need 14 x 32's sticking out and shackles to make that look right, like mine had.

That's a nice car looks like it works good too, I like the old school wheels on it. You should put some rear quarters on it. Or sell it to me, I got a BBC here, will go good in it.

That thing would clean up nice, rear quarters, paint and triple chrome plated steel bumpers.


This message has been edited. Last edited by: Mike Rietow,
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
My rear wheel opening looked exactly like yours when I got it almost 40 years ago.

That was done back in the 70's or 80's for 14 x 32 tires and shackles, I'd guess. Same as mine.

I like it, nice car. Mine had old school slotted wheels on the front as well. Skinny's with Moroso drag special tires.
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Pro
Picture of SpeierRacingHeads
posted Hide Post
Have a customer Wayne Pratt has a 406 with my heads at 2800lbs. Won a couple divisionals last year in S/ST.

https://youtu.be/VAtvNqSIGkA

 
Posts: 1404 | Location: Hays Kansas | Registered: January 23, 2006Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
quote:
Originally posted by SpeierRacingHeads:
Have a customer Wayne Pratt has a 406 with my heads at 2800lbs. Won a couple divisionals last year in S/ST.



We're talking out of JEGS magazine 23 degree conventional sbc cylinder heads at 3000 plus lbs.

AFR , Brodix, Unported All Pro conventional non raised runner, or any other out of the box un-ported.

I've been looking for something faster than Brodix out of the box, since 2017.
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2 3 4 ... 15 
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    BULLET CAMS - BRODIX sbc Track 1 heads

© DragRaceResults.com 2024