DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    T400 cross member alignment
Go
New
Find
Notify
Tools
Reply
  
T400 cross member alignment
 Login/Join
 
DRR Sportsman
Picture of Ron Gusack
posted
Factory BBC 70 Nova 4 speed car. Converted to a 400 trans with, I think, an oem cross member. Every time we install the trans, we have to pull the tailshaft toward the passenger side of the car to get the 7/16 cross member bolts to go in the trans mount. The car still has the original front subframe and when I measure inside to inside, with the cross member in, it measures about 1/2" out of center. Has anyone had this issue? Is there a line laser to put on the output shaft of the trans to see where it hits the yoke of the rear?
 
Posts: 455 | Location: Maryland | Registered: January 23, 2007Reply With QuoteReport This Post
DRR S/Pro
Picture of Lenny5160
posted Hide Post
You know, my '70 Nova had the same issue. I don't remember which way it needed to go, but the trans mount just didn't line up quite right.

I just elongated the holes in the crossmember so the bolts would go through comfortably. LOL!


Tony Leonard
 
Posts: 3148 | Location: Inver Grove Heights, MN | Registered: March 18, 2004Reply With QuoteReport This Post
DRR Pro
Picture of HS professor
posted Hide Post
I've ran into this problem a few times before and there's really no obvious reason for it. Obviously it's a subframe/motor mount issues but which one or both ??
Interesting little fact ..... Big bocks in a 69 Camaro with a 4 speed did have a BB specific crossmember, not sure about Nova's.
 
Posts: 1421 | Location: Monroe twp nj | Registered: December 05, 2005Reply With QuoteReport This Post
DRR Pro
Picture of SlyFox
posted Hide Post
Had the same issue with my 69 Chevelle. OEM build quality back in those days was sort of all over the place. You can leave the bolts loose where the cross member bolts to the frame, leave the bolts loose where the transmission mount bolts to the crossmember, and leave the bolts loose where the mount bolts to the transmission. Then you can let the transmission down off the jack to a resting position, and tighten all the bolts up wherever the transmission ultimately lands. Hope that makes sense - there's usually a little wiggle room everywhere things bolt up, and you can use that to your advantage.


Mike
 
Posts: 1562 | Location: Marietta, GA | Registered: December 09, 2005Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
I have always had an "A" body and that exists there also. I have a always secured the trans to the cross member let it down and re-drilled the holes in the frame to match the cross member or vise versa. Done it this way for many years and once its aligned like that first time the holes always matched and never any vibration or other problems
 
Posts: 6197 | Location: everywhere | Registered: March 15, 2007Reply With QuoteReport This Post
DRR Sportsman
Picture of Ron Gusack
posted Hide Post
Thanks for the replies. It helps to know that this is a fairly common issue. I like Fern's fix so I'll be drilling as soon as I get the trans back in. There's never been any issue with it but it's bothered me for 40 years. One side of the cross member is slotted and the other has holes. I hope I have enough material to slide it over and be able to drill new holes. Maybe an aftermarket cross member is in my future.
 
Posts: 455 | Location: Maryland | Registered: January 23, 2007Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
My car is a small block with a glide and does this when I have the crossmember in backwards. All the holes are slotted but it goes in a lot harder when its back wards.


Disclaimer: The opinions expressed here are the views of the writer and do not reflect the views or opinions of any entity other than myself.

72 Nova 370 ci (Stealth Black)
 
Posts: 394 | Location: Hanover, MD | Registered: July 22, 2003Reply With QuoteReport This Post



DRR Sportsman
Picture of Ron Gusack
posted Hide Post
quote:
Originally posted by Tom R:
My car is a small block with a glide and does this when I have the crossmember in backwards. All the holes are slotted but it goes in a lot harder when its back wards.

That would fit my M.O. perfectly but I don't think backwards is possible. I think the front to back fitment would be off by a few inches minimum. Mine looks similar to this: https://www.ss396.com/nova/FCM...AEAQYBCABEgKprPD_BwE
 
Posts: 455 | Location: Maryland | Registered: January 23, 2007Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
Yeah, I've never had a 400 in mine. Mine is like this below.



Disclaimer: The opinions expressed here are the views of the writer and do not reflect the views or opinions of any entity other than myself.

72 Nova 370 ci (Stealth Black)
 
Posts: 394 | Location: Hanover, MD | Registered: July 22, 2003Reply With QuoteReport This Post
DRR Trophy
Picture of ROLLIN'
posted Hide Post
quote:
Originally posted by Tom R:
Yeah, I've never had a 400 in mine. Mine is like this below.



Tom & Ron,
You are both correct about the OEM cross members. Tom the one you have posted was original for PG's/T350s in 68-72 Nova's AND 67-69 Camaro's and the same applied to the one that Ron posted (pic) is for Turbo 400's in 68-72 Nova's AND 67-69 Camaro's. Both, had the same subframe ! I remember dealing with this 45 years ago with several of my 69 Camaro's over the years. I remember elongating the holes in the frame to make it easier.
 
Posts: 21 | Location: .002 next to you | Registered: May 26, 2011Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
Check out the cross members made by Smith Racecraft. I have one in a '68 Camaro. They are light, and extremely well made with room for alignment.
 
Posts: 86 | Location: Abilene, Texas | Registered: July 30, 2018Reply With QuoteReport This Post
DRR Sportsman
Picture of 23taltered
posted Hide Post
Weren't all those cars built with the drivetrain offset 1/2" It seems like I remember reading that somewhere. If you put solid motormounts in it, they would probably be centered.


Bill Huntington
GZMOTORSPORTS.com

gzmotorsports.com/video/PRI2010.wmv
 
Posts: 163 | Location: Northern Cal | Registered: January 06, 2000Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
https://smithracecraft.com/pro...ossmembers/turbo-400


1.34 9.42@ 142.41 1.29 5.97 @ 114.00 @ #3251 Better in 2022
427 BBC by S&S Speed Center, AFD, Enderle MFI by Spud Miller
Trackside Products, Sepanek Racing T400, Dynamic converter, Autoweld, Santhuff, Smith Racecraft,
His real name is Richard but they call it "**** Fords Body Shop"
 
Posts: 105 | Location: upstate NY | Registered: January 15, 2018Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
https://www.novas.net/forums/showthread.php?t=32633


1.34 9.42@ 142.41 1.29 5.97 @ 114.00 @ #3251 Better in 2022
427 BBC by S&S Speed Center, AFD, Enderle MFI by Spud Miller
Trackside Products, Sepanek Racing T400, Dynamic converter, Autoweld, Santhuff, Smith Racecraft,
His real name is Richard but they call it "**** Fords Body Shop"
 
Posts: 105 | Location: upstate NY | Registered: January 15, 2018Reply With QuoteReport This Post



  Powered by Social Strata  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    T400 cross member alignment

© DragRaceResults.com 2024