DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Moroso Vacuum Pump Mounting SBC
Go
New
Find
Notify
Tools
Reply
  
Moroso Vacuum Pump Mounting SBC
 Login/Join
 
DRR Elite
posted
I have the typical high mount on the driver's side on the head. The problem I run into is there is very little clearance between the water pump and the belt. And I would like to go with a bit larger crank pulley. but then there is interference with the belt.

Is there a sbc mount that puts it a bit lower than the typical one I have? I do have my alternator mounted low on the driver's side. So I can't get carried away.


Foxtrot Juliet Bravo
 
Posts: 6375 | Location: Illinois | Registered: July 08, 2004Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
Can you mount it low on passenger side? I have big block but just got done mounting pump on passenger side and alternator on drivers side both down low.
 
Posts: 2591 | Location: at the track | Registered: May 09, 2007Reply With QuoteReport This Post
DRR Elite
posted Hide Post
No fuel pump and wheel pickup is there.


Foxtrot Juliet Bravo
 
Posts: 6375 | Location: Illinois | Registered: July 08, 2004Reply With QuoteReport This Post
DRR Elite
posted Hide Post
I used to have it spaced out enough that the belt was past the end of the water pump. I wasn't sure I liked it hanging out that far, but I may go back to it.


Foxtrot Juliet Bravo
 
Posts: 6375 | Location: Illinois | Registered: July 08, 2004Reply With QuoteReport This Post
DRR Trophy
Picture of NC3x58
posted Hide Post
quote:
Originally posted by green1:
Can you mount it low on passenger side? I have big block but just got done mounting pump on passenger side and alternator on drivers side both down low.


Happen to have any pictures of the vacuum pump down low?


Nick Craig

1971 Camaro Split Bumper
376ci LS3
 
Posts: 410 | Location: Ohio | Registered: December 28, 2013Reply With QuoteReport This Post
DRR S/Pro
posted Hide Post
Nick pm me your cell number and I will send you pic.
 
Posts: 2591 | Location: at the track | Registered: May 09, 2007Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
The two 3/8 threaded holes on Brodix T1 cylinder heads, come in handy.


 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post



DRR Top Comp
posted Hide Post
There is an alternator underneath the pump you can't see as well. I was originally gonna grind everything concentric, weld the aluminum and powder coat,this was in essence the mock up. It came out so rigid once all altogether and snugged down. I called it good, left it go for another day. It would be a simple mounting kit to mass produce.
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
DRR Elite
posted Hide Post
I may be able to utilize my front motor plate to do something similar position wise. I like it. Thank you.


Foxtrot Juliet Bravo
 
Posts: 6375 | Location: Illinois | Registered: July 08, 2004Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
Yes sir. You're welcome.
 
Posts: 9398 | Location: Madeira Beach Fl. | Registered: June 12, 2018Reply With QuoteReport This Post
  Powered by Social Strata  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Moroso Vacuum Pump Mounting SBC

© DragRaceResults.com 2024