DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    TBS 250 Blower Induction
Go
New
Find
Notify
Tools
Reply
  
TBS 250 Blower Induction
 Login/Join
 
DRR Sportsman
posted
What cfm carbs have you ran on the 250 blower - see any difference one carb or two. Brand also Thanks


Jeff McClure
 
Posts: 240 | Location: Texas | Registered: December 02, 2006Reply With QuoteReport This Post
DRR Pro
Picture of Alaskaracer
posted Hide Post
Most of the ones I see running the 250 blower are running a single dominator on alky. Usually about a 1600 cfm deal. Two carbs will generally always out perform a single, but there are factors involved with that.....


Mark Goulette
Owner/Driver of the Livin' The Dream Racing dragster
www.livinthedreamracing.com
"Speed kills but it's better than going slow!"
Authorized Amsoil Retailer
 
Posts: 1465 | Location: Back home in Alaska! | Registered: February 13, 2011Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
Thanks Mark - I run a 1450 currently. I was curious what others were using and if they tried one and changed and if it produced cost effective results. Maybe someone had a 1450 and changed to a 1600 what were the results. Bored I home alone this Christmas and thinking of preparing for the wet bandits HaHa


Jeff McClure
 
Posts: 240 | Location: Texas | Registered: December 02, 2006Reply With QuoteReport This Post
DRR Top Comp
Picture of Curly1
posted Hide Post
Which brings up another question are they tuning them any different for the 250 blower?


https://postimg.cc/gallery/np3zpruo/
"Dunning-Kruger Effect"
-a type of Cognitive bias where people with little expertise or ability assume they have superior expertise or ability. This overestimation occurs as a result of the fact that they do not have enough knowledge to know they don't have enough knowledge.

Before you argue with someone ask yourself, "Is this person mentally mature enough to grasp the concept of a different perspective?" If not there is no point to argue.

4X NE2 CHAMPION. 2020 TDRA NE2 Champion
 
Posts: 3964 | Location: United States of Texas | Registered: April 02, 2011Reply With QuoteReport This Post
DRR Pro
Picture of TORQIN
posted Hide Post
Have ran apd 1250, an apd 1450 and Get M biggest alky. Differences between each. Will go faster with 2 carbs without a doubt. Even faster with injection. In most cases the single carb can't supply enough fuel in really good air. Been 4.23 165 with one carb, 33 top pulley, 64 bottom pulley, steel block, 598 BB3 headed Wilson engine.

This message has been edited. Last edited by: TORQIN,
 
Posts: 1749 | Location: Houston, Tx. | Registered: November 27, 2008Reply With QuoteReport This Post
DRR Trophy
posted Hide Post
Single Ron's terminator with a buffco top here
 
Posts: 75 | Location: nitrousville | Registered: January 30, 2012Reply With QuoteReport This Post
DRR Pro
Picture of Alaskaracer
posted Hide Post
quote:
Originally posted by Nitrous1:
Single Ron's terminator with a buffco top here


^^^Better than any carb setup....


Mark Goulette
Owner/Driver of the Livin' The Dream Racing dragster
www.livinthedreamracing.com
"Speed kills but it's better than going slow!"
Authorized Amsoil Retailer
 
Posts: 1465 | Location: Back home in Alaska! | Registered: February 13, 2011Reply With QuoteReport This Post



DRR Sportsman
posted Hide Post
On the fuel injection I guess it’s all going in above the blower? Chris any difference in carbs. 1450 to 1600


Jeff McClure
 
Posts: 240 | Location: Texas | Registered: December 02, 2006Reply With QuoteReport This Post
DRR Pro
Picture of Alaskaracer
posted Hide Post
quote:
Originally posted by smokinjeff:
On the fuel injection I guess it’s all going in above the blower? Chris any difference in carbs. 1450 to 1600


Yeah, the nozzles will go into a plate right below the throttle body...You can run them in the ports, but you'll need some above the blower too to cool it and keep from running it dry. That small of a blower though not needed....above it is good enough.

Difference between carbs will depend on engine....likely the 1450 will be enough


Mark Goulette
Owner/Driver of the Livin' The Dream Racing dragster
www.livinthedreamracing.com
"Speed kills but it's better than going slow!"
Authorized Amsoil Retailer
 
Posts: 1465 | Location: Back home in Alaska! | Registered: February 13, 2011Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
Thanks Mark. Merry Christmas


Jeff McClure
 
Posts: 240 | Location: Texas | Registered: December 02, 2006Reply With QuoteReport This Post
DRR Pro
Picture of TORQIN
posted Hide Post
Bigger made more power on dyno, didn't always reflect on racetrack...bigger would be better in ideal conditions IMO.
 
Posts: 1749 | Location: Houston, Tx. | Registered: November 27, 2008Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
Thanks Chris i appreciate the reply. Hope all is well and Santa was good to you !!!


Jeff McClure
 
Posts: 240 | Location: Texas | Registered: December 02, 2006Reply With QuoteReport This Post
DRR S/Pro
Picture of The Bozman
posted Hide Post
I have two Rupert 1150's with a dual top for the 250 if you are looking, will make a great deal on the two carbs and the top for the blower.

I was going to run them on my blower but though it best to stay Naturally asperated and not try to run 4.70's bracket racing in a door car in the Texas heat.


Keeping the Socialists and NEO-LIBERALS at bay with FACTS one post at a time !!!

Freedom isn't free !!! Thank a veteran, they will actually appreciate it.
 
Posts: 2497 | Location: Gilmer, Texas | Registered: June 25, 2002Reply With QuoteReport This Post
DRR Trophy
Picture of Fabman
posted Hide Post
Anyone installed the TBS 250 blower with EFI yet?
 
Posts: 272 | Location: USA | Registered: August 27, 2022Reply With QuoteReport This Post



  Powered by Social Strata  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    TBS 250 Blower Induction

© DragRaceResults.com 2024