DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Dragsters w/ 4 calipers question
Page 1 2 
Go
New
Find
Notify
Tools
Reply
  
Dragsters w/ 4 calipers question
 Login/Join
 
DRR Top Comp
posted
New dragster has 2 calipers per wheel/ 4 total. They're Strange 4 puck calipers.
6-1 pedal ratio.
Dual master cylinders.

My question is 3/4" or 7/8" bore on the master cylinders?
Just what others are actually running.


.
Dave



F J B

 
Posts: 4447 | Location: Earth | Registered: February 08, 2006Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
Are you planning on one master cylinder for all four calipers or two in order to have two seperate braking systems? Kevin
 
Posts: 194 | Location: Corunna, Ontario, Canada | Registered: September 30, 2001Reply With QuoteReport This Post
DRR Elite
Picture of Bill Koski
posted Hide Post
If I was doing that I'd have a master cylinder for each side. That way if a hat or rotor fails you'd still have brakes.


TAKE IT TO THE BANK!!!!!
Later, Bill Koski
 
Posts: 11001 | Location: LAS VEGAS. NEVADA, US of A | Registered: December 03, 1999Reply With QuoteReport This Post
DRR Pro
Picture of CURTIS REED
posted Hide Post
quote:
Originally posted by Bill Koski:
If I was doing that I'd have a master cylinder for each side. That way if a hat or rotor fails you'd still have brakes.


That sounds kind of dangerous to me. 2 calipers working on one side.



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 2916 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post
DRR Trophy
Picture of NC3x58
posted Hide Post
quote:
Originally posted by CURTIS REED:
quote:
Originally posted by Bill Koski:
If I was doing that I'd have a master cylinder for each side. That way if a hat or rotor fails you'd still have brakes.


That sounds kind of dangerous to me. 2 calipers working on one side.


Typically the setup is dual caliper per rotor and then two master cylinders, one master cylinder controlling the front side of the calipers per rotor and then the second controlling the backside.. This setup allows you to always have equal brakes per system..


Nick Craig

1971 Camaro Split Bumper
376ci LS3
 
Posts: 410 | Location: Ohio | Registered: December 28, 2013Reply With QuoteReport This Post
DRR Sportsman
Picture of diceman1530
posted Hide Post
Should have one set on hand brake and one set on foot brake pedal.
Mark Williams has a chart on there web site on choosing master cylinder size.


Working for the Weekend!!!!
Fordyce Motorsports
 
Posts: 252 | Location: Williamstown, NJ | Registered: November 20, 2009Reply With QuoteReport This Post
DRR Pro
Picture of CURTIS REED
posted Hide Post
quote:
Originally posted by NC3x58:
quote:
Originally posted by CURTIS REED:
quote:
Originally posted by Bill Koski:
If I was doing that I'd have a master cylinder for each side. That way if a hat or rotor fails you'd still have brakes.


That sounds kind of dangerous to me. 2 calipers working on one side.


Typically the setup is dual caliper per rotor and then two master cylinders, one master cylinder controlling the front side of the calipers per rotor and then the second controlling the backside.. This setup allows you to always have equal brakes per system..


I know how it is usually done, but the way Koski stated it as "each side" makes it sound like a master cylinder for driver's side and one for passenger side not a front pair and rear pair. That is what I was referencing.

Curtis



____________________________
2017 and 2018 Osage Casinos Tulsa Raceway Park No-Box Champion

2018 Div4 Goodguys Hammer award winner
 
Posts: 2916 | Location: KIEFER, OK. | Registered: August 17, 2007Reply With QuoteReport This Post



DRR Top Comp
Picture of Curly1
posted Hide Post
On my altered I put dual brakes on it with a hand brake and separate master cylinder in case of a brake failure.


https://postimg.cc/gallery/np3zpruo/
"Dunning-Kruger Effect"
-a type of Cognitive bias where people with little expertise or ability assume they have superior expertise or ability. This overestimation occurs as a result of the fact that they do not have enough knowledge to know they don't have enough knowledge.

Before you argue with someone ask yourself, "Is this person mentally mature enough to grasp the concept of a different perspective?" If not there is no point to argue.

4X NE2 CHAMPION. 2020 TDRA NE2 Champion
 
Posts: 3973 | Location: United States of Texas | Registered: April 02, 2011Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
The very last thing I would want is having only one side of the braking system working. I'd rather go into the sand/net than an instant right/left into the wall.
I will have one m/c plumbed to the rear calipers and one m/c plumbed to the front calipers. Both m/c are on one pedal.

I was just asking what bore size m/c people with this set up were using. I'm leaning towards a 7/8" bore..


.
Dave



F J B

 
Posts: 4447 | Location: Earth | Registered: February 08, 2006Reply With QuoteReport This Post
DRR Elite
Picture of Bill Koski
posted Hide Post
An instant turn INTO THE WALL?
You must be running an open differential?
Don't feel bad, I've seen this reaction from a few other people!


TAKE IT TO THE BANK!!!!!
Later, Bill Koski
 
Posts: 11001 | Location: LAS VEGAS. NEVADA, US of A | Registered: December 03, 1999Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
I don't believe you Bill....disconnect one side of your brake system and go make a run and then hit your brakes.
Please....


.
Dave



F J B

 
Posts: 4447 | Location: Earth | Registered: February 08, 2006Reply With QuoteReport This Post
DRR Elite
Picture of Bill Koski
posted Hide Post
I did.
Years ago I had a rear caliper fail at the 1st day of a 3 day race, plugged the line to that caliper and raced the weekend with no problems other then having to use more pedal pressure.
Just think rationally here, with a spool the tires don't know where the braking is coming from!!!!!
As I posted with a MC plumbed to both sides if one rotor comes out of the caliper, or calipers, for whatever reason YOU ARE TOTALLY WITHOUT BRAKES!!!!!


TAKE IT TO THE BANK!!!!!
Later, Bill Koski
 
Posts: 11001 | Location: LAS VEGAS. NEVADA, US of A | Registered: December 03, 1999Reply With QuoteReport This Post
DRR Trophy
Picture of NC3x58
posted Hide Post
quote:
Originally posted by CURTIS REED:
quote:
Originally posted by NC3x58:
quote:
Originally posted by CURTIS REED:
quote:
Originally posted by Bill Koski:
If I was doing that I'd have a master cylinder for each side. That way if a hat or rotor fails you'd still have brakes.


That sounds kind of dangerous to me. 2 calipers working on one side.


Typically the setup is dual caliper per rotor and then two master cylinders, one master cylinder controlling the front side of the calipers per rotor and then the second controlling the backside.. This setup allows you to always have equal brakes per system..


I know how it is usually done, but the way Koski stated it as "each side" makes it sound like a master cylinder for driver's side and one for passenger side not a front pair and rear pair. That is what I was referencing.

Curtis


I guess that's what I was referencing as well.. Having 1 master cylinder for 1 wheel with two calipers would be scary I would think.


Nick Craig

1971 Camaro Split Bumper
376ci LS3
 
Posts: 410 | Location: Ohio | Registered: December 28, 2013Reply With QuoteReport This Post
DRR Pro
Picture of Roger McGinnis
posted Hide Post
quote:
Originally posted by Bill Koski:

Just think rationally here, with a spool the tires don't know where the braking is coming from!!!!!


Exactly. Our open wheel dirt cars not only have one master cylinder, they only have one caliper on the rear end. Now on the front is a different story. Still only one of each (on the left front for turning).



ΜΟΛΩΝ ΛΑΒΕ
 
Posts: 559 | Location: Republic of Texas | Registered: January 16, 2011Reply With QuoteReport This Post



DRR S/Pro
Picture of Lenny5160
posted Hide Post
quote:
Originally posted by Bill Koski:
I did.
Years ago I had a rear caliper fail at the 1st day of a 3 day race, plugged the line to that caliper and raced the weekend with no problems other then having to use more pedal pressure.
Just think rationally here, with a spool the tires don't know where the braking is coming from!!!!!
As I posted with a MC plumbed to both sides if one rotor comes out of the caliper, or calipers, for whatever reason YOU ARE TOTALLY WITHOUT BRAKES!!!!!


I had the same initial reaction as everyone else, but on my junior dragsters there is a single caliper in the center of the rear axle. Would the car react differently if that caliper was way off to one side or another? No.

It is an interesting thought, but I'd opt for two separate braking systems plumbed to both wheels. I wish I'd added the handbrake option when my car was built, but that was in the era when NHRA was confiscating brake handles.


Tony Leonard
 
Posts: 3148 | Location: Inver Grove Heights, MN | Registered: March 18, 2004Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
quote:
Originally posted by imakehp:
New dragster has 2 calipers per wheel/ 4 total. They're Strange 4 puck calipers.
6-1 pedal ratio.
Dual master cylinders.

My question is 3/4" or 7/8" bore on the master cylinders?
Just what others are actually running.



This...


.
Dave



F J B

 
Posts: 4447 | Location: Earth | Registered: February 08, 2006Reply With QuoteReport This Post
DRR Sportsman
posted Hide Post
Dave, 7/8" bore per 2 calipers with -3 (3/16") brake line. I've tried other combinations and this is what works best and I've used the Mark Williams pressure gauge to verify different working pressures with different size master cylinders and lines. Hope this helps. Kevin
 
Posts: 194 | Location: Corunna, Ontario, Canada | Registered: September 30, 2001Reply With QuoteReport This Post
DRR Elite
Picture of Bill Koski
posted Hide Post
With that much clamping pressure I'd go with 1" or even 1 1/8" MC's.
It will be real easy to lock the brakes up.


TAKE IT TO THE BANK!!!!!
Later, Bill Koski
 
Posts: 11001 | Location: LAS VEGAS. NEVADA, US of A | Registered: December 03, 1999Reply With QuoteReport This Post
DRR Pro
posted Hide Post
7/8 bore tilton masters part numbers 74-875U
 
Posts: 1424 | Location: united states | Registered: January 16, 2006Reply With QuoteReport This Post
DRR Top Comp
posted Hide Post
Thanks Kevin and Jenavet. I think I've even got a credit at Tilton...


.
Dave



F J B

 
Posts: 4447 | Location: Earth | Registered: February 08, 2006Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2  
 

DragRaceResults.Com    Bracket Talk    Bracket Talk Forum  Hop To Forum Categories  Tech Talk - by Abruzzi    Dragsters w/ 4 calipers question

© DragRaceResults.com 2024